background image

7

- Insert the cut piece of tape behind the aluminum 

guide, between the guide and the Allen screws, 

according to the same figure above.

- Push the guide against the tape, without forcing 

much so that the tape does not bend.

- Tighten the screws. The distance of the guide is 

already adjusted according to the thickness of the 

tape.

- Do not remove the piece of tape.

- With a piece of wood, make sure the guide is aligned 

with the glue axis. To make this movement push the 

wood against the aluminum guides entry sliding to 

contact the glue axis. The glue axis must move slightly 

(right of 0.5 to 1 mm) so that, when operating, passes 

the glue without hitting brusquely in the glue axis. 

Just touch lightly, passing the glue on the panel.

TAPE PLACEMENT:

 To place your tape correctly, 

follow these steps:

- Put the tape roll on the tape support previously 

installed that already came with the machine.

- Insert the tape into the tape guide as shown in the 

figure below, adjusting the knob A, so that the stops 

only guide the tape at its height, without locking it. 

Make sure, pulling and pushing the tape, you can 

move freely.

- Position the tape to the zero point, in other words, at 

the point where the wood touches the tape, taking it 

with a little left over to be cutted.

- Your tape is regulated.

The operations made by the Edgebander CBC.E, 

as well as any other machine, can pose risks to the 

operator if the instructions in this section are not 

taken into account. 

These instructions are written with the understanding 

that the operator has the knowledge and skills 

necessary to operate this machine. If at any time you 

feel  difficulty  performing  any  operation,  stop  using 

the machine. If you are an inexperienced operator, we 

recommend that you read books, technical papers, or 

seeks training from an experienced operator before 

performing any operation unknown. The machine 

must operate with all the protections and security 

systems that comes standard.

Above all, your safety must come first.

1. STARTING AND CONTROL

To turn on your CBC.E MAKSIWA proceed as follows:

- Connect the previously installed outlet at 

110V single 

phase

 supply.

- On the control panel you will find different commands. 

Get to know each of them and their functions:

1. Turn the main switch (

1

).  This  key  energizes  the 

machine’s panel, without turning it on.

2. Emergency Button (

2

)  (red  mushroom):  When 

triggered, instantly shuts down all machine controls. 

To release it, just rotate clockwise.

machine, activates other commands and starts the 

process of heating the glue. If the machine does not 

turn on and the light does not turn on when you press 

this button, make sure the main switch has been 

turned on and the emergency button is not activated.

4.  Off  Button  (

4

)  (red):  This  button  turns  off  the 

machine  by  turning  off  all  the  functions,  including 

heating the glue.

5. Feeder Switch (

5

): This button activates the feeder 

(rubber  and  glue  axis).  But  this  button  will  only  be 

released after the glue reaches the set temperature.

6. Temperature controller (6): It has two displays - the 

upper display indicates the actual temperature of the 

glue (red numbers) and the lower display shows the 

OPERATIONS

Summary of Contents for CBC.EC



















Reviews: