manualshive.com logo in svg

MAKSIWA BMS.3200.IR, Instruction Manual

Share
Download
MAKSIWA BMS.3200.IR Instruction Manual Download Page 26

26

3 Installation

The following sections will deal with the adjustments necessary for the smooth operation of the 
machine and shall refer to the term that accompanies the illustrations. For this, you must know the 
components and know where they are. 

3.1 Electrical Installation

• 

The electrical installation should be carried out by qualified and trained personnel.

•  The main connections must be made at the terminal box.
•  Installation of the power cord in the machine should only be done by a electrician.
•  Connect the machine’s power wires to an electrical outlet: 380 V, 220 V, 110 V this varies depending 

on the model of the BMS.3200.IR.

•  We recommend the installation of circuit breaker be according to the model you have purchased.

Electrical:

3 phase models:

3 phase model 380 V:

Main motor:
•  6 Amps
•  5 HP
•  Non-loaded blade speed: 4,000 RPM
Scoring motor:
•  3/4 HP
•  1.0 Amps
•  Non-loaded scoring blade speed: 8,000 RPM

3 phase model 220 V:

Main motor:
•  10 Amps
•  5 HP
•  Non-loaded scoring blade speed: 4,000 RPM
Scoring motor:
• 

3/4 HP

• 

1.5 Amps

• 

Non-loaded scoring blade speed: 8,000 RPM

3 Installation

Summary of Contents for BMS.3200.IR























































Reviews:

No comments

Brands by name

Popular brands

Load more brands