background image

6 ENGLISH

Switch action

1

►    

1.

 Switch trigger

CAUTION:

 

Before installing the battery car-

tridge into the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released.

To start the tool, simply pull the switch trigger. Tool 

speed is increased by increasing pressure on the switch 

trigger. Release the switch trigger to stop.

NOTE:

 The tool automatically stops if you keep pull

-

ing the switch trigger for about 6 minutes.

Lighting up the front lamp

CAUTION:

 

Do not look in the light or see the 

source of light directly.

1

►    

1.

 Lamp

1

►    

1.

 Button

Pull the switch trigger to turn on the lamp. To turn off, 

release it. The lamp goes out approximately 10 seconds 

after releasing the switch trigger.

To keep the lamp off, turn off the lamp status. To turn off 

the lamp status, first pull and release the switch trigger. 
And then press the button 

 for one second within 10 

seconds.

To turn on the lamp status again, press the button again 

similarly.

NOTE:

 To confirm the lamp status, pull the trigger. 

When the lamp lights up by pulling the switch trigger, 

the lamp status is ON. When the lamp does not come 

on, the lamp status is OFF.

NOTE:

 When the tool is overheated, the light flashes 

for one minute, and then the LED display goes off. In 

this case, cool down the tool before operating again.

NOTE:

 Use a dry cloth to wipe the dirt off the lens of 

the lamp. Be careful not to scratch the lens of lamp, or 

it may lower the illumination.

Reversing switch action

1

A

B

►    

1.

 Reversing switch lever

Summary of Contents for TD111DSAJ













Reviews: