background image

2 ENGLISH

SPECIFICATIONS

Model:

TD111D

Fastening capacities

Machine screw

4 mm - 8 mm

Standard bolt

5 mm - 14 mm

High tensile bolt

5 mm - 12 mm

No load speed

Hard impact mode

0 - 3,000 min

-1

Soft impact mode

0 - 1,300 min

-1

Impacts per minute

Hard impact mode

0 - 3,900 min

-1

Soft impact mode

0 - 1,600 min

-1

Rated voltage

D.C. 10.8 V - 12 V max

Overall length

135 mm

Battery cartridge

BL1016, BL1021B

BL1041B

Net weight

0.97 kg

1.1 kg

• 

Due to our continuing program of research and development, the specifications herein are subject to change 

without notice.

• 

Specifications and battery cartridge may differ from country to country.

• 

Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Symbols

The following show the symbols used for the equip

-

ment. Be sure that you understand their meaning before 

use.

Read instruction manual.

 

Cd

Ni-MH

Li-ion

Only for EU countries

Do not dispose of electric equipment or 

battery pack together with household waste 

material!

In observance of the European Directives, 

on Waste Electric and Electronic 

Equipment and Batteries and Accumulators 

and Waste Batteries and Accumulators 

and their implementation in accordance 

with national laws, electric equipment and 

batteries and battery pack(s) that have 

reached the end of their life must be col-

lected separately and returned to an envi-

ronmentally compatible recycling facility.

Intended use

The tool is intended for screw driving in wood, metal 

and plastic.

Noise

The typical A-weighted noise level determined accord

-

ing to EN60745:

Sound pressure level (L

pA

) : 94 dB(A)

Sound power level (L

WA

) : 105 dB (A)

Uncertainty (K) : 3 dB(A)

WARNING:

 

Wear ear protection.

Vibration

The vibration total value (tri-axial vector sum) deter

-

mined according to EN60745:

Work mode: impact tightening of fasteners of the maxi

-

mum capacity of the tool

Vibration emission (a

h

) : 12.5 m/s

2

Uncertainty (K) : 1.5 m/s

2

NOTE:

 The declared vibration emission value has 

been measured in accordance with the standard test 

method and may be used for comparing one tool with 

another.

NOTE:

 The declared vibration emission value 

may also be used in a preliminary assessment of 

exposure.

WARNING:

 The vibration emission during actual 

use of the power tool can differ from the declared 

emission value depending on the ways in which the 

tool is used.

WARNING:

 Be sure to identify safety measures 

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking 

account of all parts of the operating cycle such as 

the times when the tool is switched off and when it is 

running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A 

to this instruction manual.

Summary of Contents for TD111DSAJ













Reviews: