background image

5 ENGLISH

FUNCTIONAL 

DESCRIPTION

CAUTION:

 

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before adjusting or checking function on the tool.

Installing or removing battery 

cartridge

CAUTION:

 

Always switch off the tool before 

installing or removing of the battery cartridge.

CAUTION:

 

Hold the tool and the battery car-

tridge firmly when installing or removing battery 

cartridge.

 Failure to hold the tool and the battery 

cartridge firmly may cause them to slip off your hands 

and result in damage to the tool and battery cartridge 

and a personal injury.

1

2

3

►    

1.

 Red indicator 

2.

 Button 

3.

 Battery cartridge

To remove the battery cartridge, slide it from the tool 

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the 

battery cartridge with the groove in the housing and slip 

it into place. Insert it all the way until it locks in place 

with a little click. If you can see the red indicator on the 

upper side of the button, it is not locked completely.

CAUTION:

 

Always install the battery cartridge 

fully until the red indicator cannot be seen.

 If not, 

it may accidentally fall out of the tool, causing injury to 

you or someone around you.

CAUTION:

 

Do not install the battery cartridge 

forcibly.

 If the cartridge does not slide in easily, it is 

not being inserted correctly.

Battery protection system

The tool is equipped with a battery protection system. 

This system automatically cuts off power to the motor to 

extend battery life.

The tool will automatically stop during operation if the 

tool and/or battery are placed under one of the following 

conditions:

Overloaded:

The tool is operated in a manner that causes it to draw 

an abnormally high current.

In this situation, turn the tool off and stop the application 

that caused the tool to become overloaded. Then turn 

the tool on to restart.

If the tool does not start, the battery is overheated. In 

this situation, let the battery cool before turning the tool 

on again.

Low battery voltage:

The remaining battery capacity is too low and the tool 

will not operate. If you turn the tool on, the motor runs 

again but stops soon. In this situation, remove and 

recharge the battery.

Indicating the remaining battery 

capacity

Only for battery cartridges with "B" at the end of the 

model number

1

2

►    

1.

 Indicator lamps 

2.

 Check button

Press the check button on the battery cartridge to indi

-

cate the remaining battery capacity. The indicator lamps 

light up for few seconds.

Indicator lamps

Remaining

capacity

Lighted

Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE:

 Depending on the conditions of use and the 

ambient temperature, the indication may differ slightly 

from the actual capacity.

Summary of Contents for TD111DSAJ













Reviews: