Makita LS1018-R, Instruction Manual

Page: 22 / 72

22
1
2
010412
After replacing brushes, plug in the tool and break in
brushes by running tool with no load for about 10 minutes.
Then check the tool while running and electric brake
operation when releasing the switch trigger. If the electric
brake is not working correctly, have the tool repaired by a
Makita service center
After use
•
After use, wipe off chips and dust adhering to the
tool with a cloth or the like. Keep the blade guard
clean according to the directions in the previously
covered section titled "Blade guard". Lubricate the
sliding portions with machine oil to prevent rust.
•
When storing the tool, pull the carriage toward you
fully.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
ACCESSORIES
WARNING:
•
These Makita accessories or attachments are
recommended for use with your Makita tool
specified in this manual.
The use of any other
accessories or attachments may result in serious
personal injury.
•
Only use the Makita accessory or attachment
for its stated purpose.
Misuse of an accessory or
attachment may result in serious personal injury.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Steel & Carbide-tipped saw blades
M i ter s a w bl ade s Fo r s m oo th and p re cis e cu tt i ng i n var ious mater i a ls.
Co m bi nat io n
G enera l pu r pos e bl ade f o r fa s t and s m oo th r ip,
c r osscu t s and m i ter s.
C r osscu tt i ng
Fo r s m oo ther c r oss gra i n cu t s. Slic e s cl ean ly
aga i n s t the gra i n .
Fi ne c r oss cu t s Fo r s and - free cu t s cl ean ly aga i n s t the gra i n .
No n - ferr ous meta ls
m i ter s a w bl ade s
Fo r m i ter s i n a lu m i n u m , copp er , b ra ss, t ubi ng ,
and o ther n o n - ferr ous meta ls.
006526
•
Sub-fence R
•
Vise assembly (Horizontal vise)
•
Vertical vise
•
Socket wrench with hex wrench on its other end
•
Holder
•
Dust bag
•
Elbow
•
Triangular rule
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested
before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period
of ONE YEAR from the date of original purchase.
Should any trouble develop during this one year period,
return the COMPLETE tool, freight prepaid, to one of
Makita’s Factory or Authorized Service Centers. If
inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our
option, replace) without charge.
This Warranty does not apply where:
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE
PRODUCT. THIS DISCLAIMER APPLIES BOTH
DURING AND AFTER THE TERM OF THIS
WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED
WARRANTIES, INCLUDING IMPLIED WARRANTIES
OF "MERCHANTABILITY" AND "FITNESS FOR A
SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM
OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
Some states do not allow limitation on how long an
implied warranty lasts, so the above limitation may not
apply to you.
repairs have been made or attempted by others:
repairs are required because of normal wear and
tear:
the tool has been abused, misused or improperly
maintained:
alterations have been made to the tool.
EN0006-1
1. Screwdriver
2. Brush holder cap