15 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model:
LS002G
Blade diameter
216 mm
Hole (arbor) diameter (country specific)
15.88 mm / 25.4 mm / 30 mm
Max. kerf thickness of the saw blade
2.4 mm
Max. miter angle
Left 60°, Right 60°
Max. bevel angle
Left 48°, Right 48°
No load speed
4,800 min
-1
Dimensions (L x W x H)
702 mm x 551 mm x 557 mm
Rated voltage
D.C. 36 V - 40 V max
Net weight
16.4 - 17.0 kg
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
BL4020 / BL4025* / BL4040* / BL4050F*
* : Recommended battery
Charger
DC40RA / DC40RB / DC40RC
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Cutting capacities (H x W) with blade 216 mm in diameter
Miter angle
Bevel angle
45° (left)
0°
45° (right)
0°
50 mm x 312 mm
70 mm x 312 mm
30 mm x 312 mm
45° (left and right)
50 mm x 220 mm
70 mm x 220 mm
30 mm x 220 mm
60° (left and right)
–
70 mm x 155 mm
–
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
To avoid injury from flying debris, keep
holding the saw head down, after making
cuts, until the blade has come to a com-
plete stop.
When performing slide cut, first pull car
-
riage fully and press down handle, then
push carriage toward the guide fence.
When performing bevel cut, first loosen the
grip dial and tilt the carriage to the desired
angle, then tighten the grip dial.
When tilting the blade beyond the range 0°
- 45°, turn the releasing lever for 48° bevel
angle in clockwise direction.
Do not place hand or fingers close to the
blade.
Wear safety glasses.
Do not stare at operating lamp.
Summary of Contents for LS002G
