background image

2

ENGLISH

SPECIFICATIONS

Model:

HS301D

Blade diameter

85 mm

Max. Cutting depth

at 0°

25.5 mm

at 45°

16.5 mm

No load speed

1,500 min

-1

Overall length

313 mm

331 mm

Rated voltage

D.C. 10.8 V - 12 V max

Battery cartridge

BL1016, BL1021B

BL1041B

Net weight

1.6 kg

1.8 kg

• 

Due to our continuing program of research and development, the specifications herein are subject to change 

without notice.

• 

Specifications and battery cartridge may differ from country to country.

• 

Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Symbols

The following show the symbols used for the equip-

ment. Be sure that you understand their meaning before 

use.

Read instruction manual.

 

Cd

Ni-MH

Li-ion

Only for EU countries

Do not dispose of electric equipment or 

battery pack together with household waste 

material!

In observance of the European Directives, 

on Waste Electric and Electronic 

Equipment and Batteries and Accumulators 

and Waste Batteries and Accumulators 

and their implementation in accordance 

with national laws, electric equipment and 

batteries and battery pack(s) that have 

reached the end of their life must be col-

lected separately and returned to an envi-

ronmentally compatible recycling facility.

Intended use

The tool is intended for performing lengthways and 

crossways straight cuts and mitre cuts with angles in 

wood while in firm contact with the workpiece.

Noise

The typical A-weighted noise level determined accord-

ing to EN60745:

Sound pressure level (L

pA

) : 71 dB(A)

Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).

WARNING:

 

Wear ear protection.

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60745:

Work mode: cutting wood

Vibration emission (a

h,W

) : 2.5 m/s

2

 or less

Uncertainty (K) : 1.5 m/s

2

NOTE:

 The declared vibration emission value has 

been measured in accordance with the standard test 

method and may be used for comparing one tool with 

another.

NOTE:

 The declared vibration emission value 

may also be used in a preliminary assessment of 

exposure.

WARNING:

 The vibration emission during actual 

use of the power tool can differ from the declared 

emission value depending on the ways in which the 

tool is used.

WARNING:

 Be sure to identify safety measures to 

protect the operator that are based on an estimation 

of exposure in the actual conditions of use (taking 

account of all parts of the operating cycle such as 

the times when the tool is switched off and when it is 

running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

Makita declares that the following Machine(s):

Designation of Machine: Cordless Circular Saw

Model No./ Type: HS301D

Conforms to the following European Directives: 

2006/42/EC

They are manufactured in accordance with the following 

standard or standardized documents: EN60745

The technical file in accordance with 2006/42/EC is 

available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

9.4.2015

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

Summary of Contents for HS301DZ













Reviews: