background image

8 ENGLISH

Insert the drill bit into the tool. Turn the drill bit and push 

it in until it engages. 

After installing the drill bit, always make sure that the 

drill bit is securely held in place by trying to pull it out.

1

►    

1.

 Drill bit

To remove the drill bit, pull the chuck cover down all the 

way and pull the drill bit out.

1

2

►    

1.

 Drill bit 

2.

 Chuck cover

Depth gauge

The depth gauge is convenient for drilling holes of 

uniform depth. Loosen the side grip and insert the depth 

gauge into the hole on the side grip. Adjust the depth 

gauge to the desired depth and tighten the side grip 

firmly.

1

2

►    

1.

 Hole 

2.

 Depth gauge

NOTE:

 Make sure that the depth gauge does not 

touch the main body of the tool when attaching it.

Dust cup (optional accessory)

Use the dust cup to prevent dust from falling over the 

tool and on yourself when performing overhead drilling 

operations. Attach the dust cup to the bit as shown in 

the figure. The size of bits which the dust cup can be 

attached to is as follows.

Model

Bit diameter

Dust cup 5

6 mm - 14.5 mm

Dust cup 9

12 mm - 16 mm

1

►    

1.

 Dust cup

Dust cup set

Optional accessory

NOTICE:

 

Do not use the dust cup set when drill

-

ing in metal or similar.

 It may damage the dust cup 

set due to the heat produced by small metal dust or 

similar. Do not install or remove the dust cup set with 

the drill bit installed in the tool. It may damage the 

dust cup set and cause dust leak.

NOTE:

 

The standard side grip cannot be used 

with the dust cup set being installed on the tool.

 

When the dust cup set is installed on the tool, remove 

the grip from the standard side grip, and then attach it 

to the optional grip base set.

Before installing the dust cup set, remove the bit from 

the tool if installed.

Install the spacer so that the grooves on the spacer fit in 

the protrusions on the tool barrel while widening it. Be 

careful for the spring not to come off from the slit of spacer.

1

2

►    

1.

 Spacer 

2.

 Spring

Summary of Contents for HR140DWMJ













Reviews: