background image

6 ENGLISH

Overloaded:

The tool is operated in a manner that causes it to draw 

an abnormally high current.

In this situation, turn the tool off and stop the application 

that caused the tool to become overloaded. Then turn 

the tool on to restart.

If the tool does not start, the battery is overheated. In 

this situation, let the battery cool before turning the tool 

on again.

Low battery voltage:

The remaining battery capacity is too low and the tool 

will not operate. If you turn the tool on, the motor runs 

again but stops soon. In this situation, remove and 

recharge the battery.

Indicating the remaining battery 

capacity

Only for battery cartridges with the indicator

1

2

►    

1.

 Indicator lamps 

2.

 Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps 

light up for a few seconds.

Indicator lamps

Remaining

capacity

Lighted

Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE:

 Depending on the conditions of use and the 

ambient temperature, the indication may differ slightly 

from the actual capacity.

Switch action

WARNING:

 

Before installing the battery car

-

tridge into the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released.

1

►    

1.

 Switch trigger

To start the tool, simply pull the switch trigger. Tool 

speed is increased by increasing pressure on the switch 

trigger. Release the switch trigger to stop.

Lighting up the front lamp

1

2

►    

1.

 Switch trigger 

2.

 Lamp

CAUTION:

 

Do not look in the light or see the 

source of light directly.

Pull the switch trigger to light up the lamp. The lamp keeps on 

lighting while the switch trigger is being pulled. The lamp goes 

out approximately 10 seconds after releasing the switch trigger.

NOTE:

 Use a dry cloth to wipe the dirt off the lens of 

the lamp. Be careful not to scratch the lens of lamp, or 

it may lower the illumination.

Reversing switch action

1

A

B

►    

1.

 Reversing switch lever

Summary of Contents for HR140DWMJ













Reviews: