background image

P 9 /14

Do the reverse of the disassembling procedure described in <10>-1.

<10>-2. Reassembling Cylinder Section

Note: When reassembling Cylinder section, be sure to follow the instructions below;

1) Rubber ring is not reversible when installed on Cup washer 23 in Guide ring.
    The metal portion of Rubber ring 20 must face the direction of Bit side. (Fig. 20)

(4) Striker is not reversible when put into Cylinder.
      Be sure to place Striker so that the end where O ring 24 is installed faces the direction of
      Crank housing. (Fig. 23)

Fig. 23

Barrel

Cylinder section

Fig. 20

[Cross section of Rubber ring 20
  illustrated to right]

Metal portion

Plastic portion

Rubber ring 20

Cup washer 23

Guide ring

Cylinder

(Bit side)

(Crank housing side)

(Bit side)

(Crank housing side)

(Bit side)

(Crank housing
  side)

3) Insert the assembled Cylinder section to the full from Crank housing side till Cylinder guide is
    completely hidden by Barrel. (Fig. 22)   
At this time, Rubber ring 20 could fall off Cylinder section.
    However, it can be reinstalled on Cylinder section from the bit side of Barrel.

Fig. 22

(Crank housing side)

2) Cylinder guide is not reversible when installed
    on Cylinder.
    The end where O ring 46 is installed must face
    the direction of Crank housing side. (Fig. 21)

Fig. 21

O ring 46

Cylinder guide

(Bit side)

Cylinder guide

Cylinder guide

Cylinder

Striker

(Crank housing side)

(Bit side)

Place Striker as illustrated below.

O ring 24

(Crank housing side)

(Bit side)

Summary of Contents for HM0860C















Reviews: