16 ENGLISH
PARTS DESCRIPTION
►
Fig.4
1
Battery cartridge
2
Speed switching lever
3
Switch trigger
4
Lock-off button
5
Barrier
6
Protector
7
Loop handle
8
Hanger
9
Shoulder harness
-
-
-
-
-
-
ASSEMBLY
WARNING:
Always be sure that the tool is
switched off and battery cartridge is removed
before carrying out any work on the tool.
Failure to
switch off and remove the battery cartridge may result
in serious personal injury from accidental start-up.
WARNING:
Never start the tool unless it is
completely assembled.
Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Attaching the barrier
Attach the barrier to the loop handle using the screw on
the barrier.
►
Fig.5:
1.
Barrier
2.
Screw
CAUTION:
After assembling the barrier, do
not remove it.
The barrier works as a safety part
to prevent you from contacting the cutting blade
accidentally.
Installing the protector
WARNING:
Never use the tool without the
guard illustrated in place.
Failure to do so can
cause serious personal injury.
CAUTION:
Take care not to injure yourself on
the cutter for cutting the nylon cord.
Attach the protector to the clamp using bolts.
►
Fig.6:
1.
Clamp
2.
Bolt
3.
Protector
After installing the protector, remove the cutter cover
from the cutter.
►
Fig.7:
1.
Cutter
2.
Cutter cover
Before installing the cutting tool, remove the nut, cup,
and clamp washer from the spindle by turning the nut
clockwise using the box wrench while holding down the
spindle lock button.
►
Fig.8:
1.
Nut
2.
Cup
3.
Clamp washer
4.
Spindle
5.
Spindle lock button
Installing the cutting tool
NOTE:
The type of the cutting tool(s) supplied as
the standard accessory varies depending on the
countries. The cutting tool is not included in some
countries.
NOTE:
Turn the tool upside down so that you can
replace the cutting tool easily.
Cutter blade
CAUTION:
When handling a cutter blade,
always wear gloves and put the blade cover on
the blade.
CAUTION:
The cutter blade must be well pol-
ished, and free of cracks or breakage.
If the cutter
blade hits a stone during operation, stop the tool and
check the cutter blade immediately.
CAUTION:
Always use the cutter blade
with the diameter described in the section for
specifications.
►
Fig.9:
1.
Nut
2.
Cup
3.
Clamp washer
4.
Cutter
blade
5.
Spindle
6.
Guard
7.
Spindle lock
button
1.
Mount the cutter blade onto the guard so that the
arrows on the cutter blade and protector are pointing in
the same direction.
►
Fig.10:
1.
Arrow
2.
Put the clamp washer and cup onto the cutter
blade.
3.
While holding down the spindle lock button,
tighten the nut securely by the box wrench.
►
Fig.11:
1.
Spindle lock button
2.
Box wrench
3.
Loosen
4.
Tighten
To remove the cutting blade, loosen the nut while hold-
ing down the spindle lock button.
Nylon cutting head
NOTICE:
Be sure to use genuine Makita nylon
cutting head.
While holding down the spindle lock button, place
the nylon cutting head onto the spindle and tighten it
securely by hand.
►
Fig.12:
1.
Nylon cutting head
2.
Spindle
3.
Spindle
lock button
4.
Loosen
5.
Tighten
To remove the nylon cutting head, loosen the nylon
cutting head while holding down the spindle lock button.
Summary of Contents for DUR194
