13 ENGLISH
Combination of 3 rebars
#3 x #3
(10 mm x 10 mm)
#4 x #4
(13 mm x 13 mm)
#5 x #5
(16 mm x 16 mm)
#3 (10 mm)
*
#4 (13 mm)
*
#5 (16 mm)
#6 (19 mm)
#7 (22 mm)
#8 (25 mm)
*
The combination is not designed for high tying strength.
Combination of 4 rebars
#3 x #3 (10 mm x 10 mm)
#4 x #4 (13 mm x 13 mm)
#3 x #3 (10 mm x 10 mm)
#4 x #4 (13 mm x 13 mm)
#5 x #5 (16 mm x 16 mm)
NOTICE:
If there is a gap between rebars or if the tool is used at an incorrect orientation, the rebars may not be
able to be tied.
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Wear safety glasses.
Do not expose to rain.
Keep hands away from the wire reel or wire
when operating the tool.
Keep hands away from the tool tip.
Push the release lever before loading
the tie wire. Having installed the tie wire,
release the lock lever.
Ni-MH
Li-ion
Only for EU countries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household waste!
In accordance with the European Directive
on waste electrical and electronic equipment
and on accumulators and batteries and
waste accumulators and batteries, as well as
their adaptation to national law, waste elec-
trical equipment, batteries and accumulators
should be stored separately and delivered
to a separate collection point for municipal
waste, operating in accordance with the
regulations on environmental protection.
This is indicated by the symbol of the crossed-
out wheeled bin placed on the equipment.
Intended use
The tool is intended for tying rebars.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745-2-18:
Sound pressure level (L
pA
) : 82 dB (A)
Sound power level (L
WA
) : 90 dB (A)
Uncertainty (K) : 3 dB (A)
NOTE:
The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
Summary of Contents for DTR181
