Makita DCV200, Instruction Manual, Page: 5 / 24

5
Switch action
To turn on the vest, push and hold the power button
(about 1.5 seconds). To turn off, push and hold the power
button again.
Temperature adjustment
There are three temperature settings (high, medium, low).
Three LED lights means that the temperature is set to
“high”, two LED lights “medium”, and one LED light “low”.
When you switch on the vest, the temperature is set to
“high”. Each press of the power button cycles through the
vest’s temperature setting.
CAUTION:
• Hold the battery holder and the battery cartridge
firmly when installing or removing battery
cartridge.
Failure to hold the battery holder and the
battery cartridge firmly may cause them to slip off your
hands and result in damage to the battery holder and
battery cartridge and a personal injury.
Installing or removing battery cartridge to
the battery holder (Fig. 2)
for CV100D
To install the battery cartridge (5), hold it so that the
battery cartridge front shape fits to that of the battery
holder opening and slip it into place. Insert it all the way
until it locks in place with a little click.
Always insert the battery cartridge all the way until it locks
in place. If not, it may accidentally fall out of the battery
holder, causing injury to you or someone around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
To remove the battery cartridge, withdraw it from the
battery holder while pressing the buttons (6) on both sides
of the cartridge.
for DCV200
To install the battery cartridge (7), align the tongue on the
battery cartridge with the groove in the battery holder and
slip it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator (8) on the
upper side of the button, it is not locked completely.
Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out
of the battery holder, causing injury to you or someone
around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
To remove the battery cartridge, slide it from the battery
holder while sliding the button (9) on the front of the
cartridge.
Indicating the remaining battery capacity
(Only for battery cartridges with “B” at the end of the
model number.)
(Fig. 3)
Press the check button (11) on the battery cartridge to
indicate the remaining battery capacity. The indicator
lamps (10) light up for few seconds.
015658
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Use of non-genuine Makita batteries, or batteries that
have been altered, will void the Makita warranty for the
Makita tool and charger.
Attaching the battery holder to the heated
vest
for CV100D (Fig. 3)
Connect the battery holder and the power cable of the
vest. Place the battery holder in the battery holder pocket.
for DCV200 (Fig. 4)
You can hang the battery holder on the belt.
Firstly pass the vest’s power cable through the hole inside
the battery holder pocket, and connect the battery holder
and the power cable of the vest. And then hang the
battery holder on your belt.
Connecting USB device (For DCV200
only) (Fig. 5)
CAUTION:
• Connect only devices which are compatible with DC5V,
2.1A power source to the USB power supply port.
Otherwise it may cause malfunction to the battery
holder.
The battery holder (with the battery) can work as an
external power supply for USB device. Connect the USB
cable (not included) with the power supply port of the
battery holder. And then connect the other end of the
cable with the device. The USB cable can be placed
inside the vest for convenience by using the hole of the
pocket and cable holder.
FUNCTIONAL DESCRIPTION
ASSEMBLY
Indicator lamps
Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery may
have
malfunctioned.