Makita DCL180SY, Instruction Manual

Page: 13 / 76

13
Sponge filter
When the sponge filter becomes dirty, clean it as follows.
1. Remove the filter.
2. Pull out the sponge filter from between the pillars.
3. Clean the sponge filter by tapping or washing. If you
wash it, dry it out thoroughly before use.
4. Insert the sponge filter from between the pillars and
set it in the original position. Make sure that each
bottom edge of the pillar holds down the sponge fil-
ter, and there is no gap between the sponge filter
and suction opening. (Fig. 35)
Wall mount for cordless cleaner
Optional accessory
NOTE:
• The screw to mount the holder is not included. Prepare
a screw which fits with the material to screw into.
Attach the wall mount for cordless cleaner to a hard
wooden wall, beam or column, where the wall mount for
cordless cleaner can be firmly secured. Always be sure
that the wall mount for cordless cleaner is securely
attached before hanging the cleaner. (Fig. 36)
CAUTION:
• Do not hang the cleaner to the wall mount violently
or hang other appliances than the cleaner.
Things to Check Before Asking for Repairs
010051
NOTE:
• Do not attempt to repair cleaner by yourself.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Extension wand (Straight pipe)
• Nozzle
• Nozzle for carpet
• Shelf brush
• Corner nozzle
• Round brush
• Flexible hose
• Filter
• Prefilter
• High performance filter
• Wall mount for cordless cleaner
• Cyclone attachment
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Cyclone attachment (Fig. 37)
About the cyclone attachment
Using the cleaner with the cyclone attachment installed
reduces the amount of dust that enters the capsule,
which helps to prevent the suction force from weakening.
In addition, cleaning after use is also simple.
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
If the battery cartridge is left
inserted, the cleaner may start unexpectedly and result
in injury.
• Clean the mesh filter of the cyclone attachment and
the filters of the cleaner unit when they become
clogged.
Continued use in the clogged condition may
result in heating or smoke.
NOTICE:
• When the cyclone attachment is attached, do not
use the cleaner in the horizontal or upward facing
condition.
Doing so may cause the mesh filter to
become clogged.
• Always use the cleaner with the filters installed,
even when using the cyclone attachment.
Using the
cleaner without the filters installed may result in a
motor malfunction.
NOTE:
• Check that the cyclone attachment, cleaner, and
straight pipe are locked properly before use.
• Empty the dust case of the cyclone attachment and the
capsule of the cleaner when dust has accumulated.
Continued use will result in weakened suction force.
Disposing of dust
When dust has accumulated up to the full line of the dust
case, follow the procedure below and dispose of the
dust.
1. Hold the dust case firmly, press and hold the two
buttons, and remove the dust case.
(Fig. 38)
Symptom Area to be investigated Fixing method
Weak suction power
• Is capsule full of dust? • Empty dust from capsule.
• Is filter clogged? • Dust down or wash filter.
• Is the battery cartridge discharged? • Recharge battery.
Not working • Is the battery cartridge discharged? • Recharge battery.