background image

24

360 DVS Series Direct Vent Fireplaces

10006326

Operating Instructions

Only glass approved by Vermont Castings 

Group should be used on this fireplace. 

Glass Information

•  The top side and top end 

louvres are removed by simply 

lifting the louvre assembly and 

pulling the assembly away 

from the fireplace. (Fig. 36)

•  The lower side louvres are 

hinged along there lower 

edge and are folded down for 

access to components in the 

base cavity of the fireplace.

•  The lower end louvre assembly 

on the 360DVS3/ SL/ SR units 

is removed in the same man-

ner as the top louvre assem-

blies.

Louvre Removal

1.

2.

FP1227

Louvre removal

11/02

Louvre

Glass Panel

FP1227

Figure 36

Window Frame Assembly Removal

Side Window Frame Assemblies

1.  Shut off the gas supply.
2.  Allow the fireplace to cool if it has been in operation.
3.  Remove the top louvre assembly.
4.  Lower the bottom louvre assembly.
5.  Release the two clamps along lower edge of the 

frame by pulling down on clamp handles. (Fig. 37)

6.  Tilt lower edge of frame out slightly and lift window 

frame assembly up and away from the fireplace.

7.  To reinstall the window frame assembly reverse 

this  procedure.

Front Window Frame Assembly

1.  Remove the top and bottom louvre assembly.
2.  Remove the lower window trim (held in place with 

magnets).

3.  Remove both lower retaining screws. Access to 

these screws is gained through the holes along the 

lower edge of the frame behind the trim. (Fig. 38)

4.  Tilt lower edge of frame out slightly and lift window 

frame assembly up and away from the fireplace. 

5.  To reinstall the window frame assembly reverse 

the process. 

FP1228

remove glass frame

11/02

Window 

Frame 

Assembly

Lower Clamps

Window 

Frame 

Assembly

Pull Clamp 

Hook

Push 

FP1228

Fig. 37

  Window frame assembly removal.

Remove_end_glass&frame

360DVS

rev. -9-17-02     rjs

Location of Lower 

Retaining Screws

FP1445

Fig. 38

  Retaining screw.

• 

The use of any non-approved replacement glass will 

void all product warranties.

• 

Care must be taken to avoid breakage of the glass.

• 

Do not operate appliance with glass front 

removed, cracked or broken.

• 

Replacement glass (complete with gasket) is 

available through your Majestic dealer and 

should only be installed by a licensed qualified 

service person.

7!2.).'

(/4',!33

7),,

#!53%"52.3

$/./44/5#(

',!33

5.4),#//,%$

.%6%2

!,,/7#(),$2%.

4/4/5#(',!33

Summary of Contents for 360DVS2













































Reviews: