Majestic 33LDVR Installation Instructions And Homeowner'S Manual Download Page 3

3

LDVR Series Direct Vent Gas Fireplace

10007317

This gas fireplace should be installed by a qualified installer, 

preferably NFI or WETT (Canada) certified,  in accordance with 

local building codes and with current CSA-B149.1 Installation 

codes for Gas Burning Appliances and Equipment. For USA 

Installations follow local codes and/or the current National Fuel 

Gas Code. ANSI Z3.1/NFPA 54.
FOR SAFE INSTALLATION AND OPERATION PLEASE NOTE 

THE FOLLOWING:
1.  This fireplace gives off high temperatures and should be located 

out of high traffic areas and away from furniture and draper-

ies.

.  Children and adults should be alerted to the hazards of high 

surface temperatures of this fireplace and should stay away 

to avoid burns or ignition of clothing.

3.  

CAUTION: Due to high glass surface temperature children 

should be carefully supervised when in the same room as 

fireplace.

IMPORTANT:

PLEASE REVIEW THE FOLLOWING CAREFULLY

Remove any plastic from trim parts before turning the 

fireplace ON.

It is normal for fireplaces fabricated of steel to give off 

some expansion and/or contraction noises during the 

start up or cool down cycle. Similar noises are found 

with your furnace heat exchanger or car engine.

It is not unusual for your gas fireplace to give off some 

odor the first time it is burned. This is due to the curing of 

the paint and any undetected oil from the manufacturing 

process. 

Please ensure that your room is well ventilated - 

open all windows.

It is recommended that you burn your  fireplace for at 

least ten (10) hours the first time you use it. If the optional 

fan kit has been installed, place the fan switch in the 

“OFF” position during this time.

Installation & Operating Instructions

Proposition 65 Warning:

 Fuels used in gas, wood-

burning or oil fired appliances, and the products of 

combustion of such fuels, contain chemicals known to 

the State of California to cause cancer, birth defects 

and other reproductive harm.

California Health & Safety Code Sec. 549.6

WARNING: Check with your electronics manufacturer 

before installing a television or other electronic device 

above this fireplace.

1. This fireplace requires adequate ventilation and combustion 

air to operate properly. 

13. This fireplace must not be connected to a chimney flue serving 

a separate solid fuel burning fireplace.

14. When the fireplace is not in use it is recommended that the 

gas valve be left in the 

OFF

 position.

15. These units have been approved for bedroom use.

33LDVR / 36LDVR / 39LDVR / 43LDVR

Certified To

ANSI Z21.88-2009 / CSA  2.33-2009

Vented Gas Fireplace Heaters

This appliance may be installed in an aftermarket 

permanently located, manufactured home or mobile 

home, where not prohibited by local codes.

This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases, unless a certified 

kit is used. 

The  LDVR  has  been  approved  for  mobile  home 

installations.

7!2.).'

(/4',!33

7),,

#!53%"52.3

$/./44/5#(

',!33

5.4),#//,%$

.%6%2

!,,/7#(),$2%.

4/4/5#(',!33

4.  Under no circumstances should this fireplace be modified. Parts 

removed for servicing should be replaced prior to operating 

this fireplace again.

5.  Installation and any repairs to this fireplace must be performed 

by a qualified installer, service agency or gas supplier. A pro-

fessional service person should be contacted to inspect this 

fireplace annually. Make it a practice to have all of your gas 

fireplaces checked annually. More frequent cleaning may be 

required due to excess lint and dust from carpeting, bedding 

material, etc.

6.  Control compartments, burners and air passages in this fireplace 

should be kept clean and free of dust and lint. Make sure the 

gas valve and pilot light are turned off before you attempt to 

clean this fireplace.

7.  The venting system (chimney) of this fireplace should be checked 

at least once a year and if needed your venting system should 

be cleaned.

8.  Keep  the  area  around  your  fireplace  clear  of  combustible 

materials,  gasoline  and  other  flammable  vapor  and  liquids. 

This fireplace should not be used as a drying rack for clothing, 

nor should Christmas stockings or decorations be hung on or 

around the fireplace.

9.  Under no circumstances should any solid fuels (wood, coal, 

paper or cardboard etc.) be used in this fireplace.

10. The flow of combustion and ventilation air must not be obstructed 

in any way.

11. When fireplace is installed directly on carpeting, vinyl tile or 

any combustible material other than wood, the fireplace must 

be installed on a metal or wood panel extending the full width 

and depth of the fireplace.

Summary of Contents for 33LDVR

















































Reviews: