background image

Ambient Temp.  Range             -20°C ... +40°C  (-4°F ... 104°F)

Humidity Limits:                                SAMA PMC 31.1-5.2

Vibration Limits:                                SAMA PMC 31.1-5.3

RFI Limits:                                        SAMA PMC 31.1-20 to 1000

                                                          MHz up to 30V/m

Material:                                            316ss standard, optional 

                                                          Hastalloy, Monel, Kynar coated

Operating Temperature:                    -50 to 302°F  (-50 to 150°C)

Maximum Pressure:                          2000 psig @ 300°F

Range:                                             12” to 30 ft.

Supply Voltage:     

15 to 36 VDC

Repeatability: 

 

.005% of full scale or .010”,

                                                          whichever is greater

Non-Linearity: 

 

.01% of full scale or .030”,

                                                          whichever is greater

Level Sensor Accuracy: 

.01% of full scale or .020”,

                                                          whichever is greater

Analog Output Resolution:  .025% of full scale, (1) 4/20 mA

                                                          primary level.

Output:   

 

One 4-20 mA output: 

                                                          Level Option: Two Digital 

                                                          Outputs: Temperature and/or

                                                          Interface via HART only.

Calibration:                                    Zero and span field adjustable 

                                                          with push buttons or HART.

                                                          Secondary level is auto-

                                                          connect. Temperature is 

                                                          configured via HART or AMS

                                                          only.

Diagnostics:                                  On board diagnostics for 

                                                          troubleshooting via HART or 

                                                          AMS 

Dampening:                                  1 to 25 seconds (field 

                                                          adjustable) via HART

Oper. Temp. (electronics)         -58 to 185°F  (-50 to 85°C)

 

Housing:                                        Explosion Proof, Dual

                                                         Compartment, 

H

” NPT, Epoxy

                                                         Coated Aluminum 

Polarity Protection:                     Diode in series with the loop

Hazardous Location Approvals: FM - Exp Cl l , Div. I Grp. B C D, 

                                                             Cl II Grp. E F G, Cl III

CSA - Ex ia (Intrinsically Safe): Cl I, Div. I, Grp. C D

           Exp (Expl. Proof): Cl I, Div. I, Grp. B C D, Cl II, Grp. E F G, Cl III

IECEx (Expl. Proof): Ex d IIC T4

Atex (Expl. Proof): EEx d IIC T4          Ex II 2 G

The LTM-300 transmitter is available in three different configurations.  A 

single output version with only one variable that will output a 4-20 mA 

signal for level.  The second configuration is a transmitter fitted with a 

second float to provide a digital output for interface level in addition to 

the primary level output.  The third configuration is one 4-20 mA signal 

for Primary level and two additional digital signals with one for interface 

level and one for temperature output.

Configurations  two  and  three  have  independent  calibration  as  well 

as independent outputs.  These configurations have the capability for 

calibration and measurement using a HART protocol communications 

system.  The HART specifications and conditions will be discussed in detail 

under the HART COMMUNICATION section of the manual.  The temperature 

range is factory set from –50°F to 300°F.

Pushbutton Calibration

Step 1 - Move jumper to the write enable position (see below)

Step 2 - Move your float or magnet to the 4mA (0%) point on the probe

Step 3 - Press the ENTER button on the display until “Trm Snsr” is 

displayed. Press the UP arrow to display “Yes” and press ENTER.

Step 4 - The display will read “Trim Zero”. Press ENTER.

Step 5 - Move the float or magnet to the 20mA (100%) point on the 

probe.

Step 6 - The display will read “Trim Span” with a value above. Using the 

arrow buttons, input the correct distance from the zero point and press 

Enter. Calibration is now completed. 

Note: “Sel Lngth” value is factory set and should not be changed. Doing 

so will cause a level error indication.

SECTION 5.0  Calibration

SECTION 4.  Specifications

5.0 LTM-300 Output Configurations

3.2 Recommended Wiring, 

Single Loop

4

4.0 Transmitter Electrical Specifications

4.1 Transmitter Sensor Tube

FRONT PANEL

Summary of Contents for LTM-300 Series





















Reviews: