background image

 

48

MAGNUM APPLIANCES REPLACEMENT PARTS PRICE LIST

 

ORDER # 

MODEL NAME/DESCRIPTION 

 CONSUMER 

PRICING 

RP2000 

T40, Essex Igniter 

 40 

RP2001 

T40 Brick Panel, Left 

 40 

RP2002 

T40 Brick Panel, Right 

 40 

RP2004 

T40, Essex Control Board  (DC) 

 145 

RP2005 

T40, Essex AC Control Board  (Analog board, repair only) 

 145 

RP2006 T40AC 

Circuit 

Board 

(Digital electronic board) 

 145 

RP2008 

1 OHM  Jumper (DC draft motor on T40 & Essex DC units) 

 12 

RP2010 

T40, Essex DC Power Supply (RPS-300) 

 97 

RP2020 

T40, Essex, Avent  DC  2 rpm Auger Motor 

 115 

RP2022 

T40, Essex AC  2 rpm Auger Motor 

 108 

RP2025 

T40, Essex DC Combustion (draft)Blower Motor  (Motor Only) 

 165 

RP2026 

T40, Essex DC Combustion (draft) Blower Motor support plate 

 25 

RP2027 

T40, Essex DC Combustion (draft) Blower  (complete assembly) 

 298 

RP2030 

T40 AC Combustion Blower  (complete assembly) 

 134 

RP2035 

T40, Essex, Avent  DC Room Fan   

 125 

MF3541 

T40 AC Convection blower 

 142 

RP2045 

F-110 N/O Switch  (interchangeable with F-140 & F-150)

 

 12 

RP2050 

L-225 N/C Switch (manual reset) T40 / Essex 

 16 

RP2055 

T40, Essex, Hopper Pressure Switch 

 42 

RP2060 

T40 DC unit Wire Harness assembly 

 58 

RP2061 

T40 AC unit Wire Harness assembly 

 58 

RP2062 

Essex DC unit Wire Harness assembly 

 58 

RP2065 

T40 Gold Door Finish (only)  (re-finish gold door) 

 208 

RP2070 

T40 Gold Door  (complete door assembly) 

 372 

RP2072 

T40 Black Door (complete door assembly) 

 163 

RP2075 

Essex Gold Door Finish (only) (re-finish gold door) 

 208 

RP2076  

Essex Gold Door  (complete door assembly) 

 375 

RP2077 

Essex Black Door  (complete door Assembly) 

 167 

RP2080 

Gold Grill assembly  (separate) 

 97 

RP2081 

Nickel Grill Assembly (separate) 

 97 

RP2082 

Complete Black Grill assembly  (separate) 

 42 

MF3600 

Black Leg set  (separate from the unit per (4) legs) 

 95 

RP2083 

Firepot (T40 & Essex) 

 42 

RP2085 

T40, Essex Black Pedestal Base  (separate) 

 125 

RP2086 

T40I Black Insert Shroud            (separate) 

 125 

RP2087 

Essex Black Trivet  (separate) 

 42 

RP2088 

Essex Gold Trivet   (separate) 

 92 

RP2089 

Essex Nickel Trivet (separate) 

 92 

RP2090 

T40, Essex, Avent Auger Assembly 

 58 

RP2091 

Auger Bushing (set) 

 12 

RP2092 

Heat Exchanger Rake Handle 

 7 

RP2093 

Damper Spring Handle 

 7 

RP2094 

2 inch plug button 

 5 

RP2095 

Air Kit Tubing 

 10 

RP2096 

Norprene Hose ¼” ID Hose  (per foot) 

 1.6 

RP2097 Door 

Handle 

Assembly 

 25 

RP2098 

T40 / Essex Arched Glass (w/gasket) 

 47 

RP2099 

Glass Gasket (separate)  per foot  (specify T40 or Essex) 

 1.25 

RP2100 

Door Gasket (separate)  per foot  (specify T40 or Essex) 

 1.25 

RP2101 

Essex Air Kit Tubing   

 11 

RPT2806 

Extension Wire Jumper for T40 Insert  

 12 

P1315  

4 ¾” diameter draft blower blade (located in draft blower housing) 

 12 

P1316 

3” diameter blade for DC Combustion (draft) blower 

 12 

 

Summary of Contents for T40AC



















































Reviews: