USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS
Gourmet
Gas Grill
Align valve stem key
to valve chamber
lock detent and rotate
Gourmet
Gas Grill
Propane (LPG)
Gas Regulator
A10-225 LPG (Propane)
10' Gas Grill Connection Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Gourmet
Gas Grill
Gourmet
Gas Grill
Type 3
Valve
Type 3
Valve
Solenoid
Typical Marine &
R.V. Application
Gourmet
Gas Grill
Align valve stem key
to valve chamber
lock detent and rotate
Gourmet
Gas Grill
Propane (LPG)
Gas Regulator
A10-225 LPG (Propane)
10' Gas Grill Connection Kit
To other LPG
appliance
or use cap
Shut off
valve
Cylinder Valve
Gauge
Gourmet
Gas Grill
Gourmet
Gas Grill
Type 3
Valve
Type 3
Valve
Solenoid
Typical Marine &
R.V. Application
• Magma On-Board LPG (Propane) Valves & Hose Kits allow
Magma Grills to be installed within a boats existing
on-board, pre-regulated low pressure LPG (Propane) system.
• Use only
Magma Type 3 Low Pressure LPG (Propane)
Valves.
See our
Valve Application Guide
at
MagmaProducts.com
for correct valve.
• In North America use
Magma A10-225 LPG 10' Gas
Grill Connection Kit
in conjunction with
Type 3 Valve.
Outside North America check your local dealer for proper
hose and fittings.
• A primary shutoff valve
(supplied with Gas Grill
Connection Kit)
must be used with this control valve at
point of connection into your system. This allows shut off
of gas supply to hose leading to grill.
•
In Australia & New Zealand LPG fuel systems must
be installed by a certified gas technician.
MAINTENANCE
Stainless steel, contrary to popular belief, can rust. Most commonly, deposits on surface of the product will trap moisture. It is this
moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel to form a protective layer of chrome
oxide. Robbed of oxygen, this reaction does not take place and “crevice corrosion” or “surface rusting” occurs. To minimize this effect,
thoroughly clean your grill with soap and water, rinse with fresh water, and dry. Avoid using stainless steel polishes on grill exterior as
most leave a residue that may discolor when grill is heated.
Additionally, stainless steel that is exposed to high heat will change color and texture over time. The “amber” color of grill exterior
and internal components is not a failure of the stainless steel and will not affect the product’s operation. When this happens, we
recommend using
“Magma Magic” Grill Restorer
to remove the “amber” color and return grill to its original luster. However,
prolonged exposure to extreme high heat will cause chromium and nickel to “burn out” of stainless steel. At this point, stainless steel
will become more susceptible to corrosion and will start to deteriorate. We recommended replacement of internal components as
they become seriously deteriorated.
We recommend thoroughly cleaning the grill and internal components after each outing. Disassemble interior components and
remove all food residue. Use a “Scotch-Brite” pad or similar product and “Easy-Off” oven cleaner for cleaning grills interior
components, followed by thoroughly washing with soap and water, rinse with fresh water & dry. AVOID CONTACT OF OVEN
CLEANER WITH SKIN, CONTROL VALVE, IGNITER ELECTRODE & WIRE, AND BOAT SURFACE. CAUTION: DO NOT USE ANY TYPE OF
ABRASIVE PAD ON EXTERIOR MIRROR FINISH AS IT WILL SCRATCH SURFACE, USE ONLY A SOFT CLOTH. We recommend covering grill
between uses. Grill covers are available at Magma retailers or directly from Magma. See our website,
MagmaProducts.com.
After
cooking, Do Not turn grill to high heat to burn off grilling residue. The grill is not a self-cleaning oven & this extreme heat can
damage stainless steel components.
Grill Grates
-
Clean with brass wire brush while grill is warm. Use Oven & Grill cleaner for burnt-on residue. Wash with soapy water
and dry prior to storage.
Ceramic Electrode
-
Located just beside the burner, it should be kept clean of grease and debris. Be careful not to damage the
ceramic insulation or the wire. See page 5 for electrode spark adjustment.
Control Valve
-
All valves are set and tested at our factory. Do not attempt to adjust or disassemble the valve in any way.
Call Magma if you suspect it is not adjusted properly. Clean valve with a cloth and remove any debris obstructing the orifice.
Repair/Replacement Parts -
All replacement parts are readily available at your Magma Retailers or directly from Magma.
For a complete list of replacement parts, visit our website
MagmaProducts.com.
6
