background image

 

1-800-MAGLINE 

(624-5463) 

                                             www.magliner.com

Lift

Plus

®

3

Thank you for purchasing the Magliner LiftPlus®!

  If you have any questions regarding your new 

Magliner product please call our customer service department at 1-800-MAGLINE (624-5463) or 

(989) 512-1000.  Please read this manual thoroughly to become familiar with the safe operation and 

maintenance of your new LiftPlus system.

General Safety Instructions

• 

Inspect before each use for damaged and loose fasteners/connections.

• 

Inspect the unit for cracks, wear or damage.  Replace damaged components immediately.

• 

Keep hands and feet away from all moving parts.

• 

Never stand or sit on the work bench.

• 

Do not use this product to lift or to transport people.

• 

Never use as a step ladder.

• 

Never use on a moving vehicle.

• 

Never operate when any of the housing components have been removed.

• 

Keep all loose items away from the lift screw, as they may become entangled during use.

• 

Never use or store in wet environments or get any of the unit wet.  The unit may be used 

indoors or outside, but always use caution to keep the unit from getting wet; dry as soon as 

possible.

• 

Never exceed 350 lbs. capacity.  Damage to the lift and personal injury could result.

• 

Never raise or lower the work bench unless the unit is unfolded and the folding latch is 

locked.

• 

Use extreme care when raising or lowering in close proximity to other objects.  Hands 

and other items may get pinched or injured as the moving attachment passes non-moving 

objects.

• 

Never place a load’s center of gravity over the vise or work bench nose; always keep the 

load center of gravity centered on the work bench.

• 

Never tilt the unit back with a raised load.

• 

Always check that the brakes are working correctly before operating with a load.

• 

Never walk away from the unit when the folding latch is in an unlocked position.

• 

Always keep the power switch off when the unit is folded.

• 

Never go over a curb or any other multi-level transition with a raised load.

• 

Do not operate when the battery charger is plugged in.

• 

Never attempt to open the battery.  If the battery is cracked or leaking, do not recharge it - it 

must be replaced.

• 

Always use a Magliner battery charger to charge your battery.

1.  Read the Owners Manual thoroughly before first use. 

2.  Charge the LiftPlus for six hours before using it for the first time.  If the LiftPlus battery 

completely discharges, recharging will take 72 hours.  See page 5 for battery and 

charging information.

3.  The lead screw requires regular lubrication for proper working condition.  See page 13 

for maintenance schedule.

Startup Instructions

Summary of Contents for LiftPlus





















Reviews: