Madelux Classic Assembling Manual Download Page 10

19

18

Manual

Manual

Fastening of covering

Fastening of covering

Fig. 19

Fig. 22

Gr

ound le

vel

А

Б

Washers and hold-downs are installed to the end in accordance with  

Fig. 21.

long hold-down 

short hold-down 

-  washer

-- wire rotator

А

Б

Covering is fastened with screws and washers in accordance with fig.22. 

Some parts have free holes but do not mount screws with washers  in 

these holes!

door or window

short hold-down 

element 12

film

element 9-1,9-2

element 9-3,9-4

Fig. 20

Gaps in a doorway are covered with polyethylene film or “Isolone” 

polyethylene  foam  (fig.19).  For  door  sealing  in  closed  position  make  lip 

seals from strips of film or “Isolone”(fig.20).

7.

Top of the greenhouse “Dachnaya-Eco”-4 is covered with two sheets 6 x 2.1 m in size 

and every extending insert is covered with one sheet. Fasten panels to elements 1 

with screws and washers, having taken up slack between the frame and the sheet. 

Mount screws at an angle in such a way that, while tightening nuts, a screw would 

pull the edge of a panel down. In order to do that, while drilling sheets through a hole 

in the element 1, set a bore to the angle of 300 to the horizontal. Start fastening 

of covering from the center across the width of the sheet, moving gradually towards 

the edges.

Put  Scotch  tape  over  a  joint  of  ends 
of  the  greenhouse  and  top  panels 

(fig.24).

At  first,  mount  a  sheet  in  such  a  way 

that its edges are mounted on elements 

4HC

 

(fig.23).

Fasten  bottom  edges  to 

elements  1  with  screws  and  washers, 

except  elements  along  the  edges. 

After  that,  mount  another  sheet  with 

overlapping  the  previous  one,  having 

mounted screws and washers in places 

of  overlapping  in  accordance  with 

fig.23

.  Last  of  all,  mount  screws  and 

washers to edge arcs 

4НК 

and 

4ВК

 

and elements 

1

Before fastening of a sheet put Scotch tape over edges of the sheet to 

prevent it from getting dust, moisture and insects inside. 

covering

washer

screw

М4х35

element 4НС

Fig. 23

7.

9.

8.

6.

Fig. 19

element 9-1, 9-2

washer

hinge

element 12

screw М4х14

screw М4х25

screw М4х35

screw М4х40

screw М4х40

film

element 9-3,9-4

Scotch 

tape

element  4НК, 4ВК 
and 1

edge panel

End 

panel

Fig. 24

Summary of Contents for Classic














Reviews: