MADDALENA GRADUS User Manual Download Page 12

 
 

10 

When the hints 

lifetime > 10 years / > 11 years

 and 

remote sensor is mounted

 are logged, the date will not be 

recorded. 
 

11.1

 

Hint description 

Hint

 

Effect

 

Possible cause 

Memory error; during access to 
database an error occured 

No calculations are carried out. The 
register for consumption is not 
being updated. 

Defective  component 

Unexpected reset by POR, RAM-
parity, access violation 

No influence to the calculation 

The measurements since the last 
storage of data in the E

2

PROM are 

lost (max. one hour). 

Lifetime > 10 years / > 11 years 

No influence to the calculation 

Long operating time 

A removal of the GRADUS from the 
heat conductor was detected 

No influence to the calculation 

A removal of the GRADUS from the 
heat conductor 

Break of one of the measuring 
sensors 

No calculations are carried out. The 
register for consumption is not 
being updated. 

A defect on the calculator circuit 
board 

Short circuit of one of the 
measuring sensors 

No calculations are carried out. The 
register for consumption is not 
being updated. 

A defect on the calculator circuit 
board 

Reset by watch dog timer 

No influence to the calculation 

The measurements since the last 
storage of data in the E

2

PROM are 

lost (max. one hour). 

Remote sensor is mounted 

No influence to the calculation 

Remote sensor was mounted. 

12

 

D

ECLARATION OF 

C

ONFORMITY

 

 For the product described in this document we confirm, as the manufacturer, that it meets the fundamental 
requirements according to the Directive 1999/5/EC (R&TTE). 
The complete signed declaration can be found at 

www.engelmann.de

13

 

M

ANUFACTURER

 

Engelmann Sensor GmbH 
Rudolf-Diesel-Str. 24-28 
69168 Wiesloch-Baiertal 

 Germany 

14

 

C

ONTACT

 

Maddalena S.p.A. 
Via G.B. Maddalena, 2/4  
33040 Povoletto (UD) 

 Italy 

Tel.: +39.0432.634811 
Fax.: +39.0432.634820 

www.maddalena.it 

 

Summary of Contents for GRADUS













Reviews: