MADDALENA GRADUS User Manual Download Page 10

 
 

Battery lifetime, estimated 

11 years + 1 year storage 

Data storage 

132 monthly values and 132 semi-monthly values 

Display 

7  special characters 

Interfaces 

Standard: infrared 

Optional: wireless M-Bus 

Remote temperature sensor 

Sensor type 

NTC preaged 

Length of cable 

2 m 

Dimensions of cover 

height 26 mm / width 12 mm / depth 10 mm 

10

 

I

NTERFACES AND 

O

PTIONS

 

10.1

 

Optical (infrared) interface 

For the communication with the optical interface an optocoupler 

and the ‘Device Monitor’ is 

necessary. The 

optocoupler and the ‘

Device

 

Monitor’ software are available as 

accessory equipment. 

Baud rate: 2400 baud 

 

10.2

 

Radio interface wireless M-Bus (optional) 

The radio interface is for the transmission of meter data (absolute values). 

 
General information about the radio interface: 

During installation of radio components the presence of bulky obstacles directly over or in front of the housing 
must be avoided. 
The transmission quality (range, telegram processing) of radio components can be negatively influenced by 
instruments or equipment with electromagnetic emissions, such as telephones (particularly LTE mobile radio 
standard), wi-fi routers, baby monitors, remote control units, electric motors, etc. 
In addition, the construction of the building has a strong influence on the transmission range and coverage.  

The factory-setting of the clock in the heat cost allocator is standard (winter) Central European Time (GMT +1). 
There is no automatic changeover to daylight savings (summer) time. 
The radio function is deactivated upon delivery (factory-setting). See section 

Activation of the radio interface

10.2.1

 

Technical data radio 

Frequency 

868 MHz 

Transmission power 

up to 12 dBm 

Protocol 

wireless M-Bus based on EN 13757-3 

Selectable modes 

S1 / T1 / C1 

Telegrams 

-

 

short telegram AMR (in conformity to OMS-Spec_Vol2_Primary_v301): 
serial number, date/time, current consumption, due date, due date value, hint 
flag, time of hint flag 

-

 

long telegram for walk-by read-out: 
serial number, date/time, current consumption, due date, due date value,  

15 monthly values, 15 half monthly values, hint flag, time of hint flag 

Encryption 

AES: Advanced Encryption Standard; key length: 128 bits 

10.2.2

 

Radio configuration 

Parameter 

 

Possible settings

 

Factory setting 

(Battery lifetime, estimated: 11 years  + 1) 

Mode 

S1 / T1 / C1; unidirectional 

T1; unidirectional 

Transmission period   

00:00 - 24:00; any time period in the day 

7:00 am - 7:00 pm 

Summary of Contents for GRADUS













Reviews: