14
Selecting Buzzer Option – “bUZ”
To select the Buzzer Configuration, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then push the
Enter
button to enter the Con menu.
The forth selection
is the “bUZ” or Buzzer setting. Push
Next
twice to get to “bUZ” then
Enter
. If
the display is “On” push
Next
to turn it “OFF” (flashing) then push
Enter
to confirm the change (solid) and push
Enter
again to return to
“bUZ” in the Con menu. Push
Next
until “End” is displayed then push
Enter
to get back to normal operation.
Selecting Alarm Relay Setting – “ArS”
To select the Alarm Relay Setting, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then push the
Enter
button to enter the Con menu.
The fifth selection
is the “ArS” or Alarm Relay Setting. Push
Next
three times to get to “ArS” then
Enter
. If the display is “dIS” (disabled) push
Next
to change it to 900, 1000,….to 2000 (default) ppm (flashing) then push
Enter
to
confirm the change (solid) and push
Enter
again to return to “ArS” in the Con menu. Push
Next
until “End” is displayed then push
Enter
to get back to normal operation.
Selecting Alarm Relay Configuration – “Arc”
To select the
Alarm Relay Configuration
, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then push
the
Enter
button to enter the Con menu.
The sixth selection
is the “Arc” or Alarm Relay Configuration. Push
Next
four times to get to
“Arc” then
Enter
. If the relay is “nO” (normally open) push
Next
to turn it to “nC” (flashing) then push
Enter
to confirm the change (solid)
and push
Enter
again to return to “Arc” in the Con menu. Push
Next
until “End” is displayed then push
Enter
to get back to normal
operation.
Selecting Fan Relay Settings – “FrS”
To select the Fan Relay setting, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then push the
Enter
button to enter the Con menu.
The seventh selection
is the “FrS” or Fan Relay setting. Push
Next
five times to get to “FrS” then
Enter
. If the fan relay is “dIS” (disabled) push
Next
to change it to 600, 700, 800, 900, 1000 (default), 1100, 1200, 1300, 1400 or 1500
ppm (flashing) then push
Enter
to confirm the change (solid) and push
Enter
again to return to “FrS” in the Con menu. Push
Next
until
“End” is displayed then push
Enter
to get back to normal operation.
Selecting Fan Relay Delay – “Frd”
To select the Fan Relay Delay setting, in normal mode, push the
Next
button to get to “Con” or the Configuration menu. Then push the
Enter
button to enter the Con menu.
The eighth selection
is the “Frd” or Fan Relay Delay. Push
Next
six times to get to “Frd” then
Enter
. If the delay is “0” (disabled) push
Next
to change it to 1, 3, 5, or 10 minutes (flashing) then push
Enter
to confirm the change
(solid) and push
Enter
again to return to “Frd” in the Con menu. Push
Next
until “End” is displayed then push
Enter
to get back to
normal operation.
Selecting Fan Relay Minimum Runtime – “Frr”
To select the
Fan Relay Minimum Runtime
setting, in normal mode, push the
Next
button to get to “Con” or the Configuration menu.
Then push the
Enter
button to enter the Con menu.
The ninth selection
is the “Frr” or Fan Minimum Run Time. Push
Next
seven
times to get to “Frr” then
Enter
. If the runtime is “0” (disabled) push
Next
to change it to 3, 5, 10 or 15 minutes (flashing) then push
Enter
to confirm the change (solid) and push
Enter
again to return to “Frr” in the Con menu. Push
Next
until “End” is displayed then
push
Enter
to get back to normal operation.
