Mackie TT24, Quick Start Manual

Page: 43 / 130

7
Owner’s Manual
Owner’
s Manual
CD/TAPE A TALKBACK
OUT IN
CTR/MONO RIGHT LEFT
MONITOR
MAINS OUT
LINE INPUTS
AUX SENDS
1 2 3 4 5 6 7 8 9 10 11 12
L
R
C
12 Aux
Sends
CD/Tape B
Inputs CD/Tape A
Inputs/Outputs Main Outputs
R M L 1 2 3 4 5 6 7 8 R L
Ch 2: Quickstart Tutorial
3. Set the
LINE
switch to the up (mic) position.
Mute button
4. Set the 48V switch to the
down
position if the mic uses
phantom power; set it to the up position otherwise.
Set the channel gain
5. Activate the
PFL
button (right of Figure 2-2).
6. Activate channel 1’s SOLO button (above fader) to
solo the channel.
7. Provide a representative signal to the mic, watch
the meters to the right of the Touchscreen, and
listen in phones (the phones level is in the UTILITY
area).
The solo level should be between -7 and -10 dBFS.
8. Press channel 1’s SOLO button again or CLEAR
SOLO (left of PFL ) to unsolo.
Route channel 1 to Main output, Group 1, and Aux 1
9. Press and hold the L/R button in the GROUP AS-
SIGN area (Figure 2-3) and activate channel 1’s
SELECT button.
All the channel SELECT buttons light, indicating
that all channels are routed to the Main output. You
should hear your mic in the speakers connected to
MAINS OUT via the master fader.
Let’s route the mic through Group 1 instead of directly
to MAINS OUT :
10. Press and hold the
L/R
button in the GROUP AS-
SIGN area and deactivate channel 1’s SELECT
button (so it is not lit).
Channel 1 no longer sends signal to
MAINS OUT
.
11. Press and hold the Group 1 button in the GROUP
ASSIGN area and activate channel 1’s
SELECT
button.
The mic is now routed to Group 1.
12. Press and hold the
L/R
button in the GROUP AS-
SIGN area and activate Group 1’s SELECT button.
Group 1 is now assigned to LEFT and RIGHT
MAINS OUT .
Use the channel, Group, and Master fader to listen
to the mic signal in the speakers connected to
MAINS OUT .
OL
SIG
1
- +
GAIN
U
20
30
40
60
1
25
AUX
SEND
1
LINE
INPUT
SOLO
SELECT
MUTE
LINE
48V
V-Pot
knob
48 V
phantom
power button
Mic/Line
level button
Gain
knob
Overload
LED
Signal
LED
Select
button
Solo
button
Channel
fader
Mute
button
Bank/
Channel
description
RETURNS
MASTER
ANALOG
DIGITAL
GROUP ASSIGN/SELECT
MASTER
V-POT
CONTROL
AUX
SENDS
FX1 FX2
FX4 FX3
ANLG MUTE
DGTL 1
RTNS 5
MSTR
SELECT
PFL SOLO
MUTE
2
6
SELECT
SOLO
MUTE
3
7
SELECT
SOL O
MUTE
4
8
SELECT
SOLO
CTR/
MONO
L/R
SELECT
PAN
HPF
AUX
MODE
2
4
6
8
10
12
CLEAR
SOLO
TRIM
METERS
AUX
PAN
1
3
5
7
9
11
Group Assign/Select buttons
Master Center/Mono Assign button
Master Left/Right Assign button
Master Select button
Group Select buttons
V-Pot Control
Aux Sends
Bank Select
Clear Solo and
PFL buttons
Group Faders p
Group Mute buttons
Master Fader
Group Solo buttons
Aux Mode
AUX AUX
Figure 2-2 Top of channel strip (left); Bank select, Clear
Solo, PFL, V-Pot control (right)
This Quickstart Tutorial will help you begin using
the TT24 quickly and easily by providing step-by-step
instructions for its most commonly utilized tasks. Rest
assured that our team of design engineers has verified
these instructions! It may be helpful to refer to Appen-
dix B:
Configurations and Block Diagrams to see how
several useful complete systems are interconnected.
2.1 Connect Amplifier/Speakers
1. Plug in a pair of amps/speakers into the MAINS OUT
LEFT
and
RIGHT XLR
connectors (Figure 2-1).
2. Connect an amp/speaker to AUX SEND 1 .
3. Plug in headphones.
Figure 2-1 Mains and Aux Sends Outputs
2.2 Connect a Mic
This section describes how to connect a mic to chan-
nel 1, set the gain, route to groups/auxes, and engage/
adjust the variable high-pass filter.
Connect mic to channel 1
1. Plug a mic into channel 1’s XLR input (top-right of
rear panel).
2. Press the ANLG bank select button (right of
Figure 2-2).