4
.11 Horizontal driving device
4 Dismantling/Assembly
Warm gear end
1.* Round nut
7. Worm wheel
15. Worm wheel shaft
2. Frame bottom part
8. Clamp element
16. Cooling coil
3 .'
Bearing housing
9. Small ball bearing
'17. Washer.
3.1 Coring
10. O-ring
18. Nut
3.2 Seal ring
11. Gasket
19. Washer
4. Round nut
12. Bearing shield
20. Screw
5. Large ball bearing
13. Seal strip
21. Screw
6. Lock ring (left hand thread)
14. Guard
22. Corrugated shim
The bearing housing shouid normaiiy remain sitting in the frame. It should be dismahtled only when it is
necessary to replace it or the O-ring (3.1), or when the separator is to be reconditioned.
If it is to be removed, observe that the round nut (1) is locked with Loctite. The nut is therefore easier to
unscrew when heated.
The bearing housing is also fixed with Loctite.
When fitting a new bearing housing, apply .Loctite 603 on its guiding surface against the frame and Loctite
243 on the threads.
Drive motor end
1
.
,
2
.
3.
4.
5.
6
.
7.
8
.
9.
10
.
11.
12
.
13.
14.
Nut
Washer,^
Stud bolt
Screw
Stop screw
Brake pulley
Elastic plate
Screw
Spring washer
Washer
Coupling disc
Electric motor
Guide ring
Motor adapter
158
Summary of Contents for Tetra Centri A 614HGV-14C
