background image

Form 46240 

2

 

Issue 06/06 

 

 

SAFETY

 

 
 
 
 

This safety alert symbol indicates important safety messages in this manual. When you see 
this symbol, carefully read the message that follows and be alert to the possibility of 
personal injury or death. 
If this reel is used by an employee, or is loaned or rented, make certain that, prior to 
operating, the user: 
1. Is instructed in safe and proper use. 
2. Reviews and understands this manual. 

 
 

 
 

BEFORE STARTING

 

 

 
Read this manual completely and make sure you understand it before attempting assembly or operation. 
 
Study all safety messages in this manual, as well as the combine or windrower manual. 
 
Read all the safety signs on the machine. 
 
Clear the area of other persons. 
 
Clean reflective surfaces on the machine. 
 
Learn and practice safe use of controls before operating.   
 
It is your responsibility to understand and follow manufacturers' instructions on machine operation, service, 
and to observe pertinent laws and regulations. 
 
To help prevent personal injuries during assembly, operation and maintenance; use protective shoes, a hard 
hat, protective glasses or goggles, and close-fitting clothing. 
 
Provide a first aid kit for use in case of accident. 
 
 

 
 

ASSEMBLY AND SERVICE

 

 

 
Before rotating any reel not mounted on a header, be sure the reel is securely attached to stable supports at 
both ends so it cannot tip or fall. 
 
Install and maintain all recommended shields and safety signs. 
 
The reel drive must be properly shielded. Install and maintain all recommended shields and safety signs. 
 
Do not crawl under, or climb over or through the reel assembly. 

Summary of Contents for 2000-B
































Reviews: