MacDon 2000-B User Manual Download

Page: 29 / 31

Form 46240

Issue 06/06

REPAIR

PARTS

REF PART

DESCRIPTION

QTY SERIAL

NUMBER

30808

SCREW - machine, Phillips Truss Head, 5/16 NC x 3/8 inch

30280

NUT - lock, flange head, 5/16 inch NC distorted thread

REF

HARDWARE - mounting, see Mounting Package

30228

NUT - lock, flange head, 3/8 inch NC distorted thread

21484

BOLT - round head, square neck, 3/8 NC x 1-1/2 inch

30712

BOLT - flange head, 3/8 NC x 2 1/2 inch (thread full)

21569

CAPSCREW - hex head, 5/16 NC x 2 inch

30504

CAPSCREW - hex socket head, 5/16 NC x 1-1/2 inch

21472

BOLT - round head, square neck, 3/8 NC x 3/4 inch

50076

BOLT - flange head, 3/8 NC x 5/8 inch

21281

BOLT - round head, square neck, 5/16 NC x 3/4 inch

101898

SCREW - flange head, self tapping, 3/8 x 5/8 inch

21594

BOLT - hex head, 5/8 NC x 1-1/2 inch

18666

NUT - lock, 5/8 NC distorted thread

35058

Main Tube - 128 inches (3245 mm) long - 12 ft. header............................... 1

35059

Main Tube - 134 inches (3400 mm) long - 12 ½ ft. header........................... 1

35060

Main Tube - 140 inches (3550 mm) long - 13 ft. header............................... 1

35061

Main Tube - 146 inches (3705 mm) long - 13 ½ ft. header........................... 1

35064

Main Tube - 164 inches (4155 mm) long - 15 ft. header............................... 1

35065

Main Tube - 170 inches (4310 mm) long - 15 ½ ft. header........................... 1

35066

Main Tube - 176 inches (4460 mm) long - 16 ft. header............................... 1

35067

Main Tube - 182 inches (4615 mm) long - 16 ½ ft. header........................... 1

35068

Main Tube - 188 inches (4770 mm) long - 17 ft. header............................... 1

35069

Main Tube - 194 inches (4920 mm) long - 17 ½ ft. header........................... 1

35070

Main Tube - 200 inches (5075 mm) long - 18 ft. & 36 ft. (qty 2) headers .... 1

35071

Main Tube - 206 inches (5230 mm) long - 18 ½ ft. header........................... 1

35072

Main Tube - 212 inches (5380 mm) long - 19 ft. header............................... 1

35073

Main Tube - 218 inches (5535 mm) long - 19 ½ ft. header........................... 1

35074

Main Tube - 224 inches (5680 mm) long - 20 ft. header............................... 1

35075

Main Tube - 230 inches (5830 mm) long - 20 ½ ft. header........................... 1

35076

Main Tube - 236 inches (5985 mm) long - 21 ft. header............................... 1

35077

Main Tube - 242 inches (6140 mm) long - 21 ½ ft. header........................... 1

35078

Main Tube - 248 inches (6290 mm) long - 22 ft. header............................... 1

35079

Main Tube - 254 inches (6445 mm) long - 22 ½ ft. header........................... 1

35082

Main Tube - 272 inches (6905 mm) long - 24 ft. header............................... 1

35083

Main Tube - 278 inches (7060 mm) long - 24 ½ ft. header........................... 1

35084

Main Tube - 284 inches (7210 mm) long - 25 ft. header............................... 1

35087

Main Tube - 302 inches (7660 mm) long - 26 ½ ft. header........................... 1

35088

Main Tube - 308 inches (7815 mm) long - 27 ft. header............................... 1

35091

Main Tube - 338 inches (8580 mm) long - 29 ½ ft. header........................... 1

35092

Main Tube - 344 inches (8735 mm) long - 30 ft. header............................... 1

35093

Main Tube - 350 inches (8890 mm) long - 30 ½ ft. header........................... 1

Summary of Contents for 2000-B
































Search results

Summary of Contents for 2000-B

Reviews:

Related manuals for 2000-B

Brands by name

Popular brands

MacDon 2000-B, Operator'S Manual

Search results

Summary of Contents for 2000-B

Reviews:

Related manuals for 2000-B

Brands by name

Popular brands