background image

48NAT

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201  Fax: +81(6)6659-8510  E-mail: [email protected]

EM-9433  Rev.8  P. 2 / 8

 

TERMINAL BLOCK

• The terminal block is separable in two pieces.  Loosen two 

screws on top and bottom of the terminal block to sepa-
rate.

• Be sure to turn off the power supply, input signal and 

power supply to the output relays before separating the 
terminal block.

Terminal Block

Separable

Terminal Block Screw
(top & bottom)

 

AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for 
satisfying complete performance described in the data 
sheet.

COMPONENT IDENTIFICATION

50

40

30

20

10

0

10

20

30

40

50

m

3

/h

%

100 SET

H

S

Z

L

90

80

70

60

50

40

30

20

10

0

M

Brackets

Body

A

Scale Plate

Pull up the part ‘A’ when replacing the scale plate.

CJC

Sensor

INSTALLATION

 

PANEL CUTOUT  unit: mm

138

+1

–0

164 min.

Note 1:  Observe at the minimum of 3 cm above and below the units for heat dissipation.
Note 2:  No bezel is needed when the panel is cut according to the above drawings.

Panel thickness: 1.6 – 8.0 mm

Panel thickness: 1.6 – 8.0 mm

• Vertical Mounting

• Horizontal Mounting

■ 

SINGLE MOUNTING (Conform to degree of protection IP65)

138

+1

–0

138

+1 –0

L

138

+1

–0

164 min.

L

Panel thickness: 1.6 – 8.0 mm

 
L = {31.5 + 36 × (N – 1)}
(N : number of units)

Panel thickness: 1.6 – 8.0 mm

 
L = {31.5 + 36 × (N – 1)}
(N : number of units)

+1

–0

+1

–0

• Vertical Mounting

• Horizontal Mounting

■ 

CLUSTERED MOUNTING (Not conform to degree of protection IP65)

138

+1

–0

31.5

+1 –0

138

+1 –0

61.5 min.

31.5

+1

–0

Summary of Contents for 48NAT









Reviews: