STEP 2 – INSTALL DUAL CONTROL UNITS
Front Mount
The Dual Control Unit feature is configured such that only one Control Unit
can be used for Extended Option accessories. Connect all Extended Option
accessories through the Main Control Unit.
1. Referring to Figure 44 and Figure 45, run the Dual Control Cable
(19B802554P9) between locations for the Radio Unit and Auxiliary
Control Unit. Be sure to locate the P2/P3 connector assembly at the radio
unit.
2. After installing radio unit mounting hardware in the normal fashion,
connect the Dual Control Cable connector (P3) to the radio unit. Tighten
the two jackscrews on P3. Next, connect the Accessory cable
(19B802554P1, 19B802554P2, or CA101288V2) connector (P1) to the
Dual Control Cable connector (P2), and tighten the jackscrews on P2.
Connect the power cable, and install radio unit in mounting bracket.
3. After installing the Auxiliary Control Unit in the normal fashion, connect
the Dual Control Cable (P1) to Auxiliary Control Unit, and tighten
jackscrews.
4. Connect the Remote Mount Accessory cable (19B802554P6) to the
Auxiliary Control Unit.
5. A yellow Ignition Sense lead is provided on the Dual Control Cable and
the Front Mount Accessory cable. If the
“Ignition Sense”
feature is
enabled on the radio unit, it is necessary to connect only one of the
yellow leads provided, whichever is convenient. Tape back the unused
yellow lead. (See page 14 for details.)
6. Install the Speakers in convenient locations near each radio unit.
NOTE
Parallel Audio Installation Requirements
In special configurations that require both speakers to operate at
the same time (simultaneous audio), install the speakers for
parallel audio operation. For wiring information, refer to the
Parallel Audio Setup Insert section of Figure 44 and Figure 45.
Perform the following steps to install parallel audio speakers:
1. Use the two 8
Ω
speakers, part number 19A149590P12, in
place of the two 4
Ω
speakers, part number LS 102824V1.
2. Hardwire each speaker directly (without relays) as shown
It is very important to use the correct speakers for this
application. Wiring 4
Ω
speakers in this configuration may cause
damage to the radio.
55
Summary of Contents for Orion
