3. Cut off 12-18
″
from the red lead. Strip back the insulation approximately
3/8
″
on each end of the wires. Insert the wire ends into the small
openings at the end of each fuse holder section and crimp a fuse
connector to each wire. Prepare the other end of the short wire in the
same manner as in (2) and connect to the positive (+) terminal of the
battery.
NOTE
•
Do not install fuse into fuse holder until installation is
completed and all connections have been checked.
•
USA Power Cable 19B802622P3 is used only with radio
with 50 watts or less RF power output.
Figure 7: Power Cable 19B802622P1 or P3 (USA Only)
Ignition Sense (All Applications)
The fuse holder must be attached to the yellow sense lead along with the ring
terminal as follows:
1. Cut the yellow sense lead approximately 6-12" from the end to be
connected to the power source.
2. Strip the insulation from each end of the short lead and from the end of
the long lead by at least
3/8
".
3. Insert the stripped end of the long lead and one end of the short lead into
the narrow end of each fuse holder half.
4. Crimp the leads in the fuse holder halves with a crimping tool.
5. Insert the 3 amp fuse into one end of the fuse holder and join the two fuse
holder halves firmly together.
6. Attach the ring terminal to the end of the short lead and connect this lead
to the ignition "ON" sense point. (Preferably to an "Accessory" point in
the vehicle fuse panel that is switched on when the vehicle ignition
switch is in the ACCESSORY and RUN positions.)
14
Summary of Contents for Orion
