background image

FES-LS8-M100 MOTOR manual Version 1.21 

April 2020 

Page 3 of 12 

1. Important notices

 

 
Please  read  this  manual  thoroughly.  It  contains  important  information  about  your 

system, having a vital importance to the flight safety.  

Information in this document is subject to change without notice. LZ design reserves 

the right to change or improve their products and to make changes in the content of this 

material without obligation to notify any person or organization of such changes or 
improvements.  
 

1.1 Limited Warranty  
 

This motor is warranted to be free from defects in materials or workmanship for two 

years from the date of purchase. Within this period, LZ design will, at its sole option, 

repair or replace any components that fail in normal use. Such repairs or replacement will 
be made at no charge to the customer for parts and labour, the customer shall be 
responsible for any transportation cost. This warranty does not cover failures due to 

abuse, misuse, accident, or unauthorized alterations or repairs.  
 

THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN 

LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING 

ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES 
YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. IN NO EVENT 

SHALL LZ DESIGN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR 
CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR  
INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT.  

 
Some states do not allow the exclusion of incidental or consequential damages, so the 
above limitations may not apply to you. LZ design retains the exclusive right to repair or 
replace the unit or software, or to offer a full refund of the purchase price, at its sole 

discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY 
BREACH OF WARRANTY.  
 

To obtain warranty service, contact your local LZ design dealer or contact LZ design 

directly.  
 

 
 
 
 

 
 
 

 
 
 
 

 
 

© LZ design. All rights reserved

 

 

 

 

Summary of Contents for FES-LS8-M100













Reviews: