background image

 

Safety Notes 

 

Each person which is responsible for the installation, the usage of service of this unit must be 
qualified and has to follow the instruction in this manual.  

Be careful when using the device. You risk an electrical shock from high voltage, if you touch 
the wires! The device has left our company in manufactured proofed state. To maintain this 
status and to ensure a permanent safe operation, it is absolutely necessary to follow the 
safety instructions and warnings in this manual.  

Errors caused by not following these instructions are not covered by the warranty. The 
manufacturer will not accept liability for any resulting defects or problems.  

  Keep the unit away from radiators or other heat sources! 

  If the unit has been exposed to tremendous temperature changes (e.g. after 

transportation), do not turn the device on immediately. The resulting condensation 
could damage the unit. Don’t switch the unit on until the device reaches room 
temperature.  

  This device belongs to protection class I. Therefore, it is imperative that the 

green/yellow wire is connected to the earth contact or plug. The electrical connection 
must be made by a qualified person.  

  Make sure that the cable has never been squeezed or damaged by sharp objects. 

Check the device and the cables regularly.  

  If the cable is damaged, it must be replaced immediately by the manufacturer, its 

service agent or a qualified person in order to avoid danger.  

  Lenses, glasses or UV filters must be replaced if they are visually damaged, or their 

effectiveness is impaired, e.g. by broken glass or by deep scratches.  

  Ensure that wires never come in contact with other wires! Handle the power cord and 

all connections with caution! 

  Make sure that the line voltage is not higher than the voltage specified in this manual.  

  Disconnect the unit from the AC mains when it is not in use or when cleaning it. 

Disconnect the connection only by pulling the cable plug.  

  Using the fixture for the first time, can result in light smoke and odors. This is a 

normal process and does not constitute a defect.  

Risk of burns!  
Do not touch the unit during operation! The housing may reach high temperatures!  

Risk to health!  
Never look directly into the light source. Especially epileptics risk an epileptic shock. 
Disconnect the unit from the AC mains when not in use or when cleaning it.  

Defects caused by modifications of the device by unqualified handling or an unqualified 
person are not covered by the warranty.  

Keep the product away from children and unskilled people.  

There are no wear parts in the device. Maintenance and service must be performed only by 
an authorized service partner.  

 

 

Summary of Contents for B EXPO200MCW














Reviews: