11
Installing the saw rail and sawing chain
– Release the chain brake (1) (move the
hand guard back and engage it).
– Unscrew the fastening nuts (18) and
remove the chain wheel guard (19).
– Place the sawing chain onto the chain
wheel. Pay attention to the chain’s cor-
rect direction of rotation:
the direction in
which the arrow points on the chain
must match the direction marked on
the chain wheel.
– Attach the saw rail and push it towards
the chain wheel.
– Insert the sawing chain into the guiding
groove of the saw rail.
– Route the sawing chain around the saw
rail. Ensure the correct location inside the
guiding groove.
– Attach the chain wheel cover. The chain
dowel spin must engage in the hole of the
saw rail.
– Tighten the fastening nuts (18) only
slightly.
Tightening the chain
– Slightly lift the tip of the saw rail.
– Check if the sawing chain runs smoothly
by turning it manually.
– Turn the tensioning screw (17) until the
chain lies on the underside of the saw rail.
– Tighten the fastening nuts (18).
Running in the sawing chain
New sawing chain and rails must be re-tight-
ened no later than after the first five cuts. This
is normal during the run-in period; the inter-
vals between future re-adjustments will
become longer.
Filling up the fuel-oil mixture
– Store the device safely with the tank
cover for fuel-oil mixture (8) facing
upwards.
– Clean the tank cover (8) and filler neck if
necessary.
– Slowly open and remove the tank
cover (8).
– Fill up the fuel-oil mixture carefully. Do
not spill!
– Check the seal in the tank cover (8) for
damage and clean if necessary. Replace
a damaged seal immediately!
DANGER! Risk of injury!
Before the
first use, all parts must be checked to
ensure that they fit tightly and func-
tion correctly.
Improperly mounted parts can cause
severe and even fatal injuries when
using the device! This device may
only be commissioned if all parts are
mounted completely and tightly and
no part is damaged!
The saw rail must be mounted cor-
rectly (
sawing chain – p. 11).
The saw chain must be tensioned
correctly (
WARNING! Risk of injury!
An
improperly mounted saw chain
causes uncontrolled cutting behav-
iour of the device! When assembling
the chain, heed the prescribed run-
ning direction!
CAUTION! Risk of injury (cuts from
sharp edges)!
The teeth of the saw
chain are very sharp! Protective
gloves must be worn for all work on
the chain.
NOTICE! Device damage!
Make
sure that when you purchase it, the
device contains neither the fuel-oil
mixture nor oil for the saw chain.
Before commissioning the device, fill
up the fuel-oil mixture and saw chain
oil (
DANGER! Risk of injury!
Fuel is
explosive!
– Before filling up, switch off the
motor and let it cool off.
– Please strictly follow all safety
information for handling fuel.
NOTICE! Device damage!
Only use
the prescribed fuel-oil mixture
(
NOTICE! Device damage!
After fill-
ing up the fuel, you should always
check whether there is still enough
saw chain oil in the saw chain oil
tank.
GB
temp.book Seite 11 Donnerstag, 5. November 2015 8:59 08
Summary of Contents for 468419
Page 4: ...4 1 18 19 3 4 5 18 17 6 10 8 7 22 8 temp book Seite 4 Donnerstag 5 November 2015 8 59 08 ...
Page 5: ...5 4 14 20 7 9 9 13 6 11 temp book Seite 5 Donnerstag 5 November 2015 8 59 08 ...
Page 6: ...6 3 23 24 25 12 13 temp book Seite 6 Donnerstag 5 November 2015 8 59 08 ...
Page 41: ...41 temp book Seite 41 Donnerstag 5 November 2015 8 59 08 ...
