ALL PROGRAMMING IS OPTIONAL
Programming is not required for default functionality
Reset Factory Defaults
Note:
In some instances, it may be necessary to reset the
Fixture Controls and connected devices back to factory
default settings. Before beginning, make sure that all
devices are connected and powered.
1.
Rapidly tap the button on the Fixture Control three times
and hold on the fourth until the green LED begins to flash
rapidly; release button.
2.
Within 1 second of releasing the button, again rapidly tap
the button three times and the green LED will flash slowly
indicating that the unit has been reset to factory defaults.
Note:
Any associations or programming previously set up
with the Fixture Control will be erased and will need to be
re-programmed.
Vive Integral Fixture Controls
Part of the Vive System
5-year Warranty:
http://www.lutron.com/TechnicalDocumentLibrary/3601321.pdf
*Note:
These could apply to either the OEM or to the end customer.
Troubleshooting
*
www.lutron.com/support
Symptom
Solution
Sensor does not respond to motion.
Fixture control is in self-test feedback mode (sensor will not respond to occupancy detection) for 5 minutes after power up unless
button is pressed or it gets associated to a Vive system.
If self-test feedback mode has been exited by one of the two methods above, sensor will not respond to occupancy detection until
2 minutes after the power reset.
Lights do not dim or turn ON as expected.
Vive Integral Fixture control does not toggle the load.
Vive Integral Fixture Control LEDs do not respond.
Ensure that control lines are wired properly.
Verify that the driver with self-powered DALI link has the DALI power supply activated. See driver manufacturer for details.
Lights are unstable at low-end.
Adjust low-end trim. Refer to Vive documentation on www.lutron.com.
The “Raise” button on the Pico remote control does not increase
the light level.
The lights cannot be raised above the Daylighting light level using a Pico remote control. If it is critical to override the daylight level,
disable daylighting from the Vive application.
Fixture control self-test ends in blinking Red LED. This means RF
performance of the product in this fixture may not meet Lutron’s
specifications.
Review wiring and construction guidelines in the
Vive Integral Fixture Controls
App Note
(048642) at www.lutron.com. Modify as
necessary and repeat the Fixture control self-test.
Wireless Transmitter(s) cannot be associated to the
Vive Integral Fixture Control.
The maximum number of Wireless Transmitters have been associated to the Vive Integral Fixture Control. To remove a previously set
up Wireless Transmitter, tap the button used for association on the Wireless Transmitter three times, on the third tap hold for three
seconds and then tap three more times.
Customer Assistance | 1.844.LUTRON1
USA, Canada, and the Caribbean
| +1.888.235.2910
Mexico
| +1.610.282.3800
Others
| www.lutron.com
*
For set-up, programming, and troubleshooting with a
Vive system, please refer to the installation instructions
included with the Vive hub or at www.lutron.com
(NOT REQUIRED) If testing occupancy sensor
functionality (Occupancy Test Mode) (does not
apply to DFCSJ-OEM-RF):
1. Apply power to fixture.
2. Wait for Fixture Control Self-Test to complete (10 seconds)
and press the button to exit the self-test.
3. Press and hold button for 3 seconds until red LED turns on
solid to enter Occupancy Test Mode.
a. The sensor requires a 2 minute “warm up” period after
applying power. Red LED will blink during the “warm up”
period in Occupancy Test Mode.
4. Provide motion in front of sensor - lights will turn ON.
5. Lights will not turn off automatically until 5 seconds after
last motion detection.
6. Test mode will automatically exit after 5 minutes of inactivity
or by tapping the button.
(NOT REQUIRED) If testing daylight sensor
functionality (does not apply to DFCSJ-OEM-RF):
1. Apply power to fixture.
2. Wait for Fixture Control Self-Test to complete (10 seconds)
and press the button to exit the self-test. Press the button
until the light is in the ON state.
3. Shine a light source (flashlight) directly into daylight sensor
lens. Fixture lights will dim down over 1 minute (hold
flashlight steadily in place).
4. Cover daylight sensor lens/button with opaque material.
Fixture light will dim up over 1 minute (hold opaque material
steadily in place).
Programming without a Vive hub (Associating transmitters to Fixture Control):
1. Press and hold the button on the integral Fixture Control for 6 seconds until the load attached to the Fixture Control starts flashing
(every 2 seconds).
Note:
Multiple Fixture Controls can be placed into association mode by repeating Step 1 prior to moving to Step 2.
2. Hold the indicated button on each transmitter for 6 seconds. The fixture will flash to show that wireless transmitters have been
associated. Alternatively, for Radio Powr Savr occupancy/vacancy and daylight sensors, the green laser pointer can be used. See
the
Using a Green Laser to Program Lutron Ceiling and Wall-Mounted Devices App Note
(048407) on www.lutron.com for
more information. To associate another transmitter, repeat steps 1 and 2.
Test
Link
Step 1
Step 2
Lutron Electronics Co., Inc. 7200 Suter Road
Coopersburg, PA 18036-1299 USA
Lutron, Pico, Vive, Clear Connect, and EcoSystem are trademarks of Lutron Electronics Co., Inc. registered in the U.S. and other countries. Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. App Store is a service mark of Apple, Inc.
Android and Google Play are trademarks of Google LLC. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. PHILIPS is a trademark of Koninklijke Philips N.V.
OSRAM and DEXAL are trademarks of OSRAM Opto Semiconductors GmbH. iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. ©2017-2018 Lutron Electronics Co., Inc.
Programming with a Vive Hub
1.
Use an iOS
R
or Android
T
compatible device.
2.
Download the Lutron
Vive app.
3.
Open the app and follow
the instructions.
Note:
For further information
on set up, programming, and
troubleshooting with a Vive system,
please refer to the installation
instructions included with the Vive
hub or visit www.lutron.com/vive
Note:
For programming the Vive
Integral Fixture Control without a
Vive hub see below.
vive.lutron.com
X
X
Vive
