Lund 67420, Original Instructions Manual, Page: 13 / 72

13
GB
O R I G I N A L I N S T R U C T I O N S
sharp or metal utensils. Such utensils can damage the cooktop surface.
If the preparation of a dish requires the use of oil, spread it on the surface of the cooktop with
a soft brush. The appliance is not used for preparing dishes by deep-frying.
APPLIANCE OPERATION
Installation, start-up and operation of the appliance
The appliance must be unpacked and all parts of the packaging completely removed. It is recommended to keep the packaging,
as it can be helpful for further transport and storage of the appliance.
Prepare the appliance according to the instructions speci fi ed in the “Product Maintenance” section.
The grill can be placed on the base provided with the grill or used as a table grill, in which case the bowl should be placed on a
table or other base.
Mounting the base supplied with the grill should start with mounting the legs to the fastening of the pedestal centre. The hooks of
each leg should be placed in the guides (II). Secure the fastening from below with a connector. The connector must be mounted
to each leg using screws (III). Place the mounted legs on a fl at, hard and even surface and check that all legs are in contact with
the surface (IV). Otherwise repeat the mounting procedure.
Slide the shorter part of the pedestal in the mounting opening (V). Screw the threaded rod (VI) into the opening in the centre of the
pedestal, and then place the decorative nut (VII) on the pedestal. Using a threaded rod, connect both parts of the pedestal (VIII).
Screw the screw in the top wall opening of the pedestal (IX), on which the shelf will rest. You can choose between two shelf-mount-
ing heights. Slide the shelf onto the pedestal so that the notch in the edge of the shelf opening rests on the screw head (X).
Slide the grill bowl onto the pedestal (XI).
Slide the drip tray through the opening in the rear grill wall and slide the bowl rod (XII) through the opening in the edge of the drip tray.
Mount the grill plate in the bowl. Start the mounting by inserting the plate’s electrical socket into the opening in the edge of the bowl
(XIII). Then mount the plate in the bowl so that the edge of the bowl is parallel to the entire circumference of the plate edge (XIV).
Mount the thermometer in the lid opening with the nut (XV). Tighten the nut without the use of tools. Tightening the nut too much
can damage the thermometer.
Slide lid plates in the bowl notches to form the guides (XVI). Check that the lid can be freely opened and closed. The opened lid
should remain in this position (XVII).
Check that the thermostat knob is set to “MIN”, then insert the plug with thermostat into the grill plate socket (XVIII). The pin of
the plug should fi t in the socket. Connect the plug so that the thermostat knob faces upwards. The shelf has a notch in the rear
edge in which the power cord should be inserted (XIX). This will minimise the risk of the power cord coming into contact with the
hot surface of the grill plate.
The plug with the thermostat can be disconnected by pressing the button on the thermostat (XX). This enables the plug to be
disconnected with one hand, thus minimising the risk of hands coming into contact with the hot grill plate.
The grill plate temperature can be set using the thermostat knob, the higher the set number, the higher the grill plate temperature.
When the grill plate heats up, the light next to the thermostat knob lights up. The thermostat automatically controls the grill plate
temperature, each time the grill plate is heated up, it is signalled by the light coming on. The frequency at which the heater switches
is determined by the set temperature and the ambient temperature. The higher the set temperature and the lower the ambient tem-
perature, the more often the heater will be switched on. A grill with an open or removable lid will heat up the grill plate more often.
The surface of the grill plate is divided into a ribbed part, which can be used for grilling and a smooth part for traditional cooking.
When using the grill, check the condition of the drip tray so that it is not over fl owing. The drip tray can be pulled out and inserted
without removing the grill plate. Grasp the drip tray with a heat-resistant glove.
WARNING! The grill plate and lid can be very hot. Take special care when using the grill. Use gloves which protect against high
temperatures.
The shelf is not resistant to high temperatures. Before putting tools on the shelf, cool them down.
Turn the thermostat knob to “MIN” after use. Disconnect the power cord plug from the mains socket and then from the grill plate
socket. Open the lid and allow all elements of the grill to cool down. Do not accelerate the cooling of the grill in any way, e.g. by
pouring water over it.
Appliance maintenance
CAUTION! All maintenance must be carried out with the appliance switched o ff . To do this, unplug the power cord from the
socket.
The appliance is used to prepare food placed directly on the cooktop, therefore care must be taken to maintain proper hygiene so
that the preparation of food is safe.