Lumina Power CCPF-500 Series User Manual Download Page 14

02100005  Rev 1 

CCPF-500 CCPF-750 User Manual 

Page 14 of 17 

 

6.

 

Warnings   

 

 

 
 

 

 

 

 

 

 

 

WARNING

:  Only Lumina Power, Inc. qualified service personnel are allowed to 

remove the covers and service this equipment. 

WARNING

NEVER OPERATE THE POWER SUPPLY:

 

1.

 

Without providing adequate protection of personnel from high voltage. 

2.

 

Without proper ground connections. 

3.

 

Without covers and panels properly installed. 

4.

 

With customer interlocks defeated. 

5.

 

Without a suitable load for the application and properly rated for the 
required power dissipation. 

 

Warning:

   

To avoid risk of electric shock, this equipment must only be 
connected to supply mains with protective earth 

Warning: 

Equipment is not suitable for use in presence of a flammable 
anesthetic mixture with air or with oxygen or nitrous oxide. 

Warning: 

These power supplies are not provided with any isolation 
devices and shall only be used inside other equipment that has 
means to isolate its circuits electrically from the supply mains 
on all poles simultaneously.   

High Voltage Present

This power supply produces lethal high voltages.  Only service 
personnel of Lumina Power, Inc., are qualified to service this 
equipment.  Only qualified service personnel are permitted to 
install this power supply.  

Warning: 

This equipment produces high voltages, which can be fatal.  
Only service personnel of Lumina Power, Inc. are qualified to 
service this equipment. 

Summary of Contents for CCPF-500 Series


















Reviews: