Cushions & Mattresses
PVC/ PU Leather Covered
The cushions in your Lumberjack Unit are PVC covered & cannot be machine washed. To clean them only use soft cleaning
equipment such as sponges, dish cloths & soft bristled brushes.
Using abrasive cleaning products will damage or scratch the seats.
If required, you can use a mild or weak mix of detergent in combination with soft cleaning equipment to remove any dirt.
The PVC seats are air dry only. Under no circumstances should the cushions be put in an electrical dryer system.
For serious stains specialised seat cleaners can be used, these can be purchased from most supermarkets.
Please Note: DO NOT use any kind of abrasive cleaner e.g. Bleach as this will break down the fibres in the PVC & drastically
reduce the life of the cushions. Avoid using detergents or cleaners containing concentrated detergents, oils, waxes, solvents,
acid bases or abrasive elements.
Fabric Covered cushions & Mattresses
Spot Cleaning
For spot cleaning of the seats use warm water & a sponge or dishcloth in a wiping motion to remove mild to light marks from the
seat.
For more deep set marks a gentle detergent can be used in combination with warm water and a wiping motion as mentioned
above. If these do not remove the mark or stain proceed to the full washing instructions as below.
Full Washing
Remove the cover from the cushion and place into a domestic washing machine, generic washing powder can be used.
Ensure your machine is set to a cold water wash & the zips on the cover are fully done up.
Once washed avoid letting the cover dry in direct sunlight as this may lighten the fabric colour over time.
Ensure the cushion cover dries completely before putting it back on the cushion & returning it to your Lumberjack Unit.
Tip: To ensure the zips stay shut during the wash cycle you can use a safety pin threaded through the zip to the fabric to prevent
it from coming undone during the wash cycle. If using this process, please remember to remove the safety pin before returning
the cover to your Lumberjack Unit.
Floors
The floors on your Lumberjack Unit are made from vinyl material or floating floorboards & need to be cleaned carefully as a
result. To clean your floors only use soft cleaning equipment such as sponges, dish cloths or soft bristled brushes in combination
with warm water & mild detergents.
When cleaning the floors use minimal water as the floor may warp if excessive water is used. If moping is required, dry mop only
& allow the Lumberjack Unit to dry completely with the doors open before closing it up for storage.
Please Note: DO NOT use any kind of abrasive or strong cleaner as this can remove the protective coating on the vinyl leaving it
susceptible to further damage or staining.
DO NOT use large quantities of water when cleaning the flooring as this will cause them to warp. Leaving moisture on the floor
while in use or in storage may cause damage to the flooring. Ensure it is completely dry before closing up your unit.
Seating Base
The seating base is made from a wood laminate & can be cleaned using the same technique as the floors, please see the above
paragraph.
Carpet (Exterior Drawers)
To clean the carpet inserts within the toolbox drawers firstly remove them from the drawers & brush off any surface dirt should
there be any.
If washing is required to remove further dirt, a mild detergent can be used along with a hard bristled brush to scrub the carpet
clean. Before cleaning the whole carpet test your detergent on a small area of the corner to ensure the detergent you wish to use
will not cause colour runoff.
Once scrubbed the carpet can be hosed down to remove any detergent residue. After cleaning ensure the carpet is left to fully
dry before returning it to the Lumberjack Unit.
Kitchen Unit (Stainless Steel)
Microfibre cloth & mild detergent.
Use a small amount of mild detergent or non-abrasive cream cleanser and warm water on a microfibre cloth and use a circular
motion at first to clean over the whole Unit. After the initial clean go over it again with only warm water to remove any detergent
residue, then wipe the whole Unit over with a dry cloth to dry the Unit.
During this last step wipe in the direction of the grain of the stainless steel, like wood, stainless steel has a grain, for the best
finish wipe in the direction of this grain.
Specified stainless steel cleaners can also be used.
It is highly recommended to wipe down the kitchen Unit after each use, do not allow dirt or food residue to sit on the surface for
prolonged periods of time as this can stain the steel.
Please Note: DO NOT use abrasive cleaners or scourers when cleaning as they can permanently scratch the surface.
D07 Rev I
41
Summary of Contents for Camper Trailer
Page 1: ...CARE MAINTENANCE MANUAL ...
Page 52: ......
