background image

Table of Contents 

 

Table of Contents 

 

PART I: General Safety Rules ......................................................................................................... 2

 

PART II: Familiar with the Wood Chipper ....................................................................................... 8

 

PART III: Operating the Wood Chipper ........................................................................................... 9

 

PART IV: Maintaining the Wood Chipper ...................................................................................... 11

 

PART V: Troubleshooting and Parts List ........................................................................................ 13

 

 

 
Conventions used in this manual 
 

 

 

WARNING 

This indicates a hazardous situation, which, if not avoided, could result in death or serious 
injury. 

 

 

 

CAUTION 

This  indicates  a  hazardous  situation,  which,  if  not  avoided,  could  result  in  minor  or 

moderate injury. 

 

 

 

NOTICE 

This  information  is  important  in  proper  using  of  your  machine.  Failure  to  follow  this 

instruction could result in damage to your machine or property. 

 

 

 

Additional Information and Potential Changes 

 

We reserve the right to discontinue, change, and improve its products at any time without 
notice or obligation to the purchaser. The descriptions and specifications contained in this 
manual were in effect at printing. Equipment described within this manual may be optional. 
Some illustrations may not be applicable to your machine.

Summary of Contents for RAMBO-HC10


















Reviews: