Lucent Technologies STGR-LIM-VD-24, Manual, Page: 26 / 102

Share

Page: 26 / 102

Lucent Technologies STGR-LIM-VD-24 Manual Download Page 26

............................................................................................................................................................................................................................................................

Line activation

The AL-DMT interface profile

2 - 6

363-217-032R9.9.0

Issue 2, March 2006

............................................................................................................................................................................................................................................................

Line activation

Description

The line is enabled by setting the

enabled

parameter to

yes

and then saving the

al-dmt

profile. Before changing this setting ensure that other line parameters have been
configured as needed and saved.

Example

The following parameters in the

al-dmt

profile, shown with their default settings, are

associated with basic line activation. Other parameters and subprofiles are described later.

[in AL-DMT/{ any-shelf any-slot 0 }]

name = ""

physical-address* = { any-shelf any-slot 0 }

enabled = no

sparing-mode = inactive

dsl-type = adsl

...

«
...
24
25
26
27
28
...
»

Summary of Contents for STGR-LIM-VD-24







































































































Reviews:

No comments