background image

Tempair 

3 in 1 Exhaust Fan 

Installation Instructions 

 

 

 

 

7

  | 

P a g e  

 

        V e r   1 . 3

 

 

 

MAINTENANCE 

1. 

Turn off power before cleaning or replacing heat lamp. 

2. 

Ensure the appliance has cooled before touching. 

3. 

The LED light source cannot be replaced. 

4. 

Use only warm soapy water and a soft cloth to clean the fascia and glass panel. 

 

Removing/Replacing the Heat Lamp 

 

 

 

 

 

 

 

 

 

 

 

 

1) 

Ensure the Tempair Fan is switched OFF and cooled. Then remove the glass fascia. 

2) 

Twist and un-plug the LED lamp connector. 

3) 

Remove the heat lamp by pushing at one end of the lamp to allow the heat lamp to free, as both 
ends of the lamp holder secures the lamp via springs.   

4) 

Replace the heat lamp. Ensure that the lamp caps are seated correctly in the lamp holder. 

5) 

Reconnect the LED lamp connector and replace the glass fascia. 

SPECIFICATIONS 

 

SKU # 

200290 

200291 

Colour 

White 

Silver 

Rated Voltage 

220-240V~ 50Hz

 

Total Rated 

Wattage 

1047W 

(Heater Unit & Ducted Fan)

 

Lamp Holder 

R7s type (500W heat lamp)

 

Weight (approx) 

Heater (4.2 Kg) / Fan (1.8 Kg)

 

Dimensions 

Heater unit (L515mm, W:360mm, H:165mm) 

Fan unit (L:280mm, W:245mm, H:240mm)

 

 
 

Fig. 7 

Summary of Contents for Tempair 200290










Reviews: