![Lubing TwinClean Line Assembly Instructions Manual Download Page 11](http://html.mh-extra.com/html/lubing/twinclean-line/twinclean-line_assembly-instructions-manual_1945597011.webp)
Drinking systems
floor watering system TwinClean Line
Copyright © 2018 Lubing System - All rights reserved
11
3.4.2.3 Fitting the water connection kit
The Clamp must be secured to the 3⁄4”
pipe
. Do this by drilling a hole
10
mm in diameter
(2)
in the water pipe.
Securing the clamp:
1. insert the clamp
(3)
and thorn in the drilled hole on the pipe.
2. make sure the O-ring seal is positioned correctly.
3. place the top part of the clamp
(1)
on the pipe and secure using the
two screws.
4. secure one end
(5)
of the hose to the hose connector
(4)
using the
clip.
5. screw the hose connector to the flat packing in the clamp
(3)
. Insert
the other end of the hose into the pressure regulator
(6)
hose connector
and secure with a clip. This must be installed with flat packings in the
case of ball valve
(7)
(see versions on the previous page). If required, the
ball valve can be mounted between the pressure regulator and the hose
connector (see graphic on right) if you wish to have the ball valve directly
on the drinking line. Or you can mount it between the hose connector
(4)
and the clamp
(3)
in order to block the water supply directly at the supply
point.
3.4.2.4 Glued connections
LUBING recommends “Tangit” adhesive, article no. 4405, for glued connections.
Many connection elements in the LUBING product range are designed as glued connections. Please observe the
following manufacturer instructions in order to ensure secure connections.
The pipe must be cut at a right angle and burred. The areas to be glued must be clean and dry. Clean the ends
of the pipe on the outside and the connecting elements on the inside using a cleaning agent (please check
compatibility) and woven felt. Always use new woven felt. The areas to be glued must be fully dry before applying
the adhesive.
Push the pipe and connecting element without twisting until the limit stop and hold tight for a few seconds until the
glue has set. Immediately following joining, remove superfluous glue with the woven felt as otherwise the pipe will
be etched too strongly. Owing to the fast setting features of the adhesive, the join parts must be pushed together
within 4 minutes of applying the glue. The open period for Tangit depends on the ambient temperature and/or film
thickness.
Stress
: do not move the pipes for at least 5 minutes after gluing. At temperatures below 10°C, this period is
extended to a minimum of 15 minutes.
Pressure test
: the pipes should not be filled nor should a pressure test be carried out until 24 hours after the last
gluing procedure. We recommend rinsing pipes and possibly even leaving them full of water if they are not put into
operation immediately.
Please observe the protective measures described by the manufacturer.
Please also observe additional information in the data sheets and guidelines on the prevention of accidents supplied
by the professional associations, e.g. VBG 15, VBG 81, M017 and the safety data sheets.
WARNING
Ensure that there is no water in the pipe before drilling.
Burr the drill hole. Rinse out any chips from the pipe. Do not
commence assembly of the clamp until after rinsing first.
AMBIENT TEMPERATURE
PROCESSING TIME
FILM THICKNESS
20 °C
approx. 4 min.
1 mm
25 °C
3 min.
1 mm
30 °C
2 min.
1 mm
40 °C
1 min.
1 mm
> 40 °C
< 1 min.
1 mm
Item no. 4155
Clamp ø3⁄4", hose connector, 5 m tube 1⁄2", ball valve and clips
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com
lubingsystem.
com