background image

macnaught.com

5     

Lubemate | Digital Preset Oil Control Gun

INSTRUCTION MANUAL

2. Installation

Pre-installation procedure

1)  Relieve the system pressure
  i) Turn off the power supply to the pump or close the shutoff valve.
   ii)  Dispense any fluid in the system into a waste container by opening the dispense valve.
  iii) Open all bleed-type master air and fluid drain valve in the system.
  iv) Leave the drain valve open until ready to pressurize the system.
2)  Close the shutoff valve.
3)   Ground hoses and reels:
 Grounding reduces the risk of static sparking; ground all system 

components according to local, state, and federal codes. Consult the user’s manual on  
the pump and other system components to ground the following:

  i) Pump: follow manufacturer’s recommendations.
  ii) Air and fluid hoses: use only grounded hoses.
  iii) Air compressor: follow manufacturer’s recommendations.
  iv) Fluid supply container: follow the local code. 

WARNING!

Do not use Teflon tape on pipe joints; it may cause a loss of grounding across the joint. 

Apply meter to hose

Close the drain valve before starting this
procedure.
1.   Attach swivel to meter .Apply thread sealant to  

the male end of the hose. Recommended sealant .

2.   Insert the metal end of the hose into the swivel. 

Tighten completely with an open end adjustable 
wrench.

NOTE:

 

The threaded end of the meter always has

female threads. The meter end of the hose must
have male threads. Apply thread sealant, anaerobic
adhesive or equivalents, to the male end. The inlet
and outlet swivel connections are 1/2” NPT 1/2”
BSP, depending on meter model.

Attach the hose 

1.  On the opposite end, apply sealant to the end of the nozzle.

2.   Thread the nozzle onto the meter. Screw it in tightly with an 

open ended, adjustable wrench.

3.   Open all dispense position shut-off-valves. start the pump to 

pressurize system.

4.   Before use to ensure accuracy. Purge all air from the fluid 

lines and dispense valve(s).

AREA 4:

 

FOR BATTERY CAPACITY

AREA 2:

 FOR MEASUREMENT UNITS

Value

ER14250 3.6V 

1-35L/min 
0.5-100bar 

Data

Flow rate

Operating Pressure Range

60°C

±0.5%

Accuracy

Battery

Max operation temperature

1

2

3

4

5

6

Fig. 2

1. Air supply

2. Shut off air valve

3. Oil Pump

4. Shut off oil valve

5. Hose reel

6. Oil control valve 

Display and button usage

 

Notes: It will flashing when

battery voltage less than 3.3V;

AREA 1:

 

FOR LAST DISPENSE CYCLE

AREA 3:

 

FOR ACCUMULATED TOTAL

Menu:

 

MOVING THE NUMBERS FOR

ADJUSTING THE CALIBRATION 

AND CHOOSING THE UNITS

Reset:

 

CHOOSING THE UNITS AND 

SETTING CORRECTION FACTOR

AREA 4:

 

FOR BATTERY CAPACITY

AREA 2:

 FOR MEASUREMENT UNITS

Value

ER14250 3.6V 

1-35L/min 
0.5-100bar 

Data

Flow rate

Operating Pressure Range

60°C

±0.5%

Accuracy

Battery

Max operation temperature

1

2

3

4

5

6

Fig. 2

1. Air supply

2. Shut off air valve

3. Oil Pump

4. Shut off oil valve

5. Hose reel

6. Oil control valve 

Display and button usage

 

Notes: It will flashing when

battery voltage less than 3.3V;

AREA 1:

 

FOR LAST DISPENSE CYCLE

AREA 3:

 

FOR ACCUMULATED TOTAL

Menu:

 

MOVING THE NUMBERS FOR

ADJUSTING THE CALIBRATION 

AND CHOOSING THE UNITS

Reset:

 

CHOOSING THE UNITS AND 

SETTING CORRECTION FACTOR

Apply nozzle to meter 

3. Operating the meter

Attach the hose

 

WARNING!

After using the manual anti-drip valve, it is important to discharge the pressure between the chambers 
(1) and the manual valve (2) of the spout. First, the pump must be switched off. Then, unscrew the tip of 
the valve (2). During this discharging operation, do not use the trigger (3).

MAC0619_Lubemate_InstructionManual_L-DPOCG_D2.indd   5-6

7/8/18   4:43 pm

Summary of Contents for L-DPOCG










Reviews: