LS SV-xxx-iP5A-2, Manual

Page: 80 / 138

Chapter 5
– Parameter List
5-14
CODE
Comm.
Addr
Description
LCD
Keypad
Display Setting Range
Factory
Default
Adj.
During
Run
Page
4 (PSI) 5 (Pa)
I/O-87 9457 Unit Maximum Selection Unit Max Val 1.0 to 999.9[%] 100[%] X
I/O-90 945A Inverter Number Inv No. 1 to 250 1 O
6-48
I/O-91
(22)
945B Baud Rate Selection Baud rate
0 (1200 bps)
3 (9600
bps)
O
6-37
1 (2400 bps)
2 (4800 bps)
3 (9600 bps)
4 (19200 bps)
5 (38400 bps)
I/O-92 945C
Operating method
at loss of freq. reference
COM Lost
Cmd
0 (None)
0 (None) O
6-48
1 (FreeRun)
2 (Stop)
3 (Lost Preset)
I/O-93 945D
Waiting time after loss of freq.
reference
COM Time
Out
0.1 to 120 [sec] 1.0 [sec] O
I/O-94 945E Communication Response Delay time Delay Time 2 to 1000 [msec] 5 [msec] O
6-48
I/O-95 945F A or B contact
In No/Nc
Set
00000000000
/11111111111
0000000
0000
X 6-49
I/O-96 9460 Input time
In
CheckTime
1 to 1000 1 [msec] X
6-49
I/0-97 9461 Overheat trip selection OH Trip Sel 000 to 111 [bit] 010 [bit] X
6-49
I/0-98 9462 Motor overheat trip temperature
MotTripTe
mp
0 to 255 [
℃
] 110 [
℃
] X
I/0-98
(23)
9463 Lost Cmd Pre freq Setting Lost Preset 0 to 60 [Hz] 0 O
6-50
* The gray-highlighted codes are hidden parameters and will appear when the related functions are to be set.
(17) When DRV-04 is set to either V1, V1S, I or V1+I or Pulse, only selected item codes are displayed in I/O-1~I/O-19.
(18) I/O-3,5,8,10,14,16 is displayed 0~100.00 [**] when App-02 is set to [proc PI mode] or APP-80 is set to [Ext PI
mode] and APP-06 PID Feedback Signal Selection is set to one of I, VI, Pulse, after then, one of I/O-86 ~I/O-88 is
set to percentage, Bar, mBar, kPa, Pa except for Speed. Unit will be changed to selected unit.
Only user unit displayed when APP-02 or APP-80 is set to [Yes], after APP-06 is set to one of I, V, Pulse, after then
one of I/O-86 ~I/O-88 is set to either speed, percentage, Bar, mBar, kPa, Pa.
(19) I/O-30 ~ I/O-34 displayed only when one of I/O-20 ~ I/O-27 is set to either JOG, Speed_L, Speed_M, Speed_H.
I/O-35 ~ I/O-42 displayed only when one of I/O-20 ~ I/O-27 is set to Speed_X.
(20) I/O-52 ~ I/O-63 displayed only when one of I/O-20 ~ I/O-27 is set to either XCEL_L, XCEL_M, XCEL_H.
(22) 38400 bps can be set only when the external communication option card is installed.
(23) I/O-99 displayed only when one of DRV-04 is set to
[V1, V1S, I, V1+I, Pulse].