LS tractor R4041 Operator'S Manual Download Page 74

Page: 74 / 125

①

Hitch

Vertical load : 900kg (1984 lbs)

Hitch

Fixing pin

Hitch pin

(8) Hitch and Drawbar (option)

When attaching towing equipments, use the hitch

or drawbar. DO NOT use the 3-point linkage or

other parts. If so, the tractor could turnover.

Insert the hitch pin and snap pin correctly after

attaching/detaching equipment.

DO NOT exceed the maximum permissible

vertical and horizontal load as below.

Horizontal load : 3600kg (7937 lbs)

②

Drawbar

Vertical load : 400kg (Long position) (882 lbs)

575kg (Short position) (1268 lbs)

Horizontal load : 2800kg (6173 lbs)

③

Drawbar w/clevis

Vertical load : 400kg (Long position) (882lbs)

575kg (Short position) (1268lbs)

Horizontal load : 2800kg (6173lbs)

Fixing pin

Connecting pin

Drawbar

Drawbar
w/clevis

Hitch pin

Fixing pin

- 16

▶

Pulling from the tractor rear axle or any point above the axle may cause the tractor

to overturn. Use always the drawbar or hitch for pulling work.

▶

Do not tow equipment without brakes, weighing more than twice the tractor weight.

▶

When locking the hitch or drawbar with pin after aligning to the towing equipment,

apply the parking brake and stop the engine.

▶

Before transporting equipment on public roads, make sure you comply with your

local traffic regulation.

Caution

Fixing pin

Summary of Contents for R4041






























































































































Search results

Summary of Contents for R4041

Reviews:

Related manuals for R4041

Brands by name

Popular brands

LS tractor R4041, Operator'S Manual

Search results

Summary of Contents for R4041

Reviews:

Related manuals for R4041

Brands by name

Popular brands