background image

1 - 22

9. Location : On the left-hand side of the hood 

rear cover.

CAUTION

- PTO selector & lever must be in “OFF” position 

to start engine.

- Do not operate on hard surfaces with 4WD 

engaged.

WARNING

- TO PREVENT SERIOUS INJURY OR DEATH;

After first hour of operation and daily thereafter, 

check front and rear wheel lug nuts and bolts 

for proper torque.

PTO - keep hands, feet and clothing away from 

PTO & other moving parts.

Disengage PTO and shut off engine before 

servicing tractor or implements, or attaching / 

detaching implements.

Keep all safety shields in place for your 

protection.

Pull only from approved drawbar or lower links 

of 3-point hitch at horizontal position or below.

Lock tractor brake pedals together for travel on 

roads or highways.

Always apply parking brake and shift 

transmission to neutral before dismounting.

Always use a seat belt when you operate the 

tractor.

Allow no riders on tractor or implements.

Do not use a seat belt when operating with 

folding ROPS in lowered position.

Engine exhaust fumes can cause death or 

sickness. Always try to work in a ventilated 

area.

Disengage the differential lock when turning 

the tractor. Always disengage the differential 

lock when driving on roads.

Depress on or both brake pedals to disengage 

the differential lock.

- Failure to comply could result in death or 

serious injury.

- Part No. : 40195656

Summary of Contents for J2023H


















































































































Reviews: