background image

5 - 32

System

Faults

Possible causes

Solutions

Brake

Brake does not work or

only one side works.

Wrong brake pedal play.

Lining worn or broken

Left/right pedal play is different

Adjust

Replace

Adjust

After brake pedal 

working, it does not

return.

Return spring damaged

Lack of grease in shaft parts

Replace the spring

Remove the rust, apply grease

Hydraulic 

lift

system

The linkage does not 

move up.

Lack of transmission oil

Air in the suction pipe

Hydraulic filter clogged

Hydraulic pump failure

Control valve failure

Cylinder or cylinder related 

parts broken

Aid oil

Tighten the filter or replace 

seal of connecting part

Clean the filter or replace

Repair or replace

Repair or replace

Repair or replace

Oil leakage

Connecting part loosened

Oil seal damaged

Pipe cracked

Tighten

Replace

Replace

If lever is placed on the 

raising position, relief 

valve sounds off.

Upper limit of position control 

lever is changed

Adjust the upper limit

The linkage does not 

move down.

Down speed control valve    

locked

Control valve failure

Cylinder damaged

Lift shaft moving part damaged

Turn the knob counter-

clockwise

Repair or replace

Replace

Repair or replace

Summary of Contents for J2023H


















































































































Reviews: