background image

features' performance could be degraded if the transducer is too far
away from the broadband sounder transducer.

Ú

Note: 

The Active Imaging 3-IN-1 transducer includes a

broadband sounder. As a result, the DownScan Overlay and
FishReveal broadband images work perfectly every time since
the images come from the same place.

< 0.3m (1f

t)

Transom and step mount (Transom

bracket)

The transducer can be mounted to the transom or step with the
transom bracket. With these mounting options the transducer can
be in the water when you are on plane, or can be mounted so it is
only in the water when you are moving at trolling speed.

Transom and Step mount (fiberglass) supplies (not

included)

3 mm (1/8”) Drill bit (Transom
mount pilot holes)

Marine high-grade above- or
below-waterline sealant/
adhesive compound

Transom mount (aluminum hull) supplies (not included)

M4 Machine Screws

Marine high-grade above- or
below-waterline sealant/
adhesive compound

Plastic isolating material such as King Starboard (prevents
corrosion between bracket and aluminum hull)

Installation

 | Active Imaging transducers Installation Manual

9

Summary of Contents for Active Imaging 3-IN-1

























Reviews: