background image

Installation

Mounting options

The transducer can be mounted on the transom, jackplate, or step.
Use the following table to determine which mounting option is
best suited to your boat/installation preferences.

Ú

Note: 

When installing, keep the transducer on the protective

foam nest where the transducer is placed from factory.

Ú

Note: 

Before drilling any holes, ensure that holes are drilled in a

safe position. Ensure you do not drill into tanks, reservoirs,
hoses, or cables, etc. and that the holes will not weaken the
structure in any way.

Ú

Note: 

When mounting the transducer, make sure there is

nothing around the mounting location that could interfere with
its sonar beams.

Ú

Note: 

If mounting where the transducer comes out of the

water, for example when the boat is on plane, the sonar will not
work while the transducer is out of the water.

A

B

C
D

E

X

 

A

Jackplate mount (Transom bracket)

 

B

Direct Step mount (Flush bracket)
Requires separately sold Skimmer Flush mount kit
(part no. 000-12602-001)

 

C

Step mount (Transom bracket)

 

D

Transom mount (Transom bracket)

6

Installation

 | Active Imaging transducers Installation

Manual

Summary of Contents for Active Imaging 3-IN-1

























Reviews: